When electrical cables get moved around and bent a lot, sometimes the outer jacket can get ripped and expose the electrical wires inside. This is especially common in frequently used cables like phone and laptop chargers. If you are starting to see exposed wires in your electrical cables, fix them as soon as possible to prevent the problem from getting worse. Fix minor damage on any type of electrical cable with electrical tape, repair damaged charger cables with Sugru putty, or fix more serious damage on electrical cables with heat-shrink tubing. If you have a cable that is extremely worn out and its electrical wires keep getting exposed because of new tears in the outer jacket, it’s probably best to replace it.

Method 1
Method 1 of 3:

Wrapping Minor Damage with Electrical Tape

  1. 1
    Stick electrical tape over the exposed wire and wrap it around once. Peel up the end of the tape from a roll of electrical tape and center it over the area of the cable with the exposed wire. Press it down on top of the exposed section and wrap it tightly around the damaged area 1 full revolution.[1]
    • You can get electrical tape in different colors, so you can try to find a color that most closely matches the cable you want to repair.
    • This method works to repair minor damage in any type of electrical cable. Keep in mind that the electrical tape can get worn out and torn over time, so you might have to replace it eventually with a fresh layer.
    • Examples of cables you could repair with electrical tape are phone or laptop chargers, power cables on electrical appliances, and headphone cords.

    Warning: Don’t use duct tape or any other type of tape to cover exposed wire. Electrical tape is insulated and specially made for electrical applications.

  2. 2
    Wrap the tape tightly around the wire 2-3 more times and cut it. Continue to wrap the tape around the damaged area, directly on top of the first revolution you made. Cut or tear the tape when you complete 2-3 more full wraps and stick the end down.[2]
    • Wrapping the tape more than once will help this quick fix last longer and help prevent further damage to the cable.
    Advertisement
  3. 3
    Make 3-4 wraps of tape on either side of the first area you taped. Stick the end of the electrical tape on the cable just to the side of the damaged area you already taped around, overlapping it slightly with the first section of tape. Wrap it around the cable 3-4 times, then cut or tear it. Repeat this for the other side of the first taped area.[3]
    • Covering the undamaged areas of the cable to the side of the area with the exposed wire that you wrapped first will strengthen the cable and help prevent further damage to the area.
  4. Advertisement
Method 2
Method 2 of 3:

Repairing Charger Cables with Sugru

  1. 1
    Tear open a packet of Sugru and knead it for about 30 seconds. Rip open a pack of single-use Sugru and pull out the silicone rubber putty. Squish it back and forth between your fingers for about 30 seconds to warm it up and make it more moldable.[4]
    • Sugru is a type of moldable, adhesive silicone rubber putty that hardens into a rubber-like outer jacket when it cures.

    Warning: Do not use Sugru putty for high-voltage cables or DIY electrical work. Only use this method to fix exposed wires in low-voltage cables like electronic device chargers or headphone cords.[5]

  2. 2
    Roll the putty out into a long, thin rectangular shape. Place the putty on a flat surface and roll it back and forth with your fingers until it becomes long and thin. Press it down with your hand until it flattens into more of a rectangle, so you can wrap it around your cable.[6]
    • A piece of Sugru that is about as long as the width of your hand will provide good coverage of the exposed wire and relieve strain on the cable to prevent further damage.
  3. 3
    Wrap the Sugru putty around the damaged area and smooth it out. Center the Sugru over the section of cable with the exposed wire and wrap it around the cable tightly. Press the edges of the putty together where they meet and firmly rub the Sugru with your fingertips to smooth out the seam and remove any fingerprints.[7]
    • If the area you’re repairing is close to the wall adapter or power adapter end of the cable, make sure to press the Sugru right up against the power block or the charger plug to create a smooth-looking repair. You can shape it to make it look like a part of the cable.
  4. 4
    Let the putty cure for 24 hours. Hang the cable up or lay it out on a flat surface somewhere out of the way. Leave it alone for a full 24 hours, so the Sugru has time to cure completely.[8]
    • The putty will turn into a strong, flexible protective casing around the exposed wire. This will prevent further damage to the area.
  5. Advertisement
Method 3
Method 3 of 3:

Applying Heat-Shrink Tubing to Electrical Wires

  1. 1
    Choose 2:1 ratio heat-shrink tubing with a diameter 2x bigger than your cable. Heat-shrink tubing with a ratio of 2:1 means it will shrink to half its diameter when you heat it up. Heat-shrink tubing that is twice the diameter of your cable and has a 2:1 ratio will shrink to the exact same diameter as your cable to seal and repair the damaged area.[9]
    • Heat-shrink tubing is a type of shrinkable plastic tubing that you can use to cover and insulate wires. You can use a hair dryer or heat gun to heat it up and shrink it.
    • For example, if your cable has a diameter of 1 mm, use 2:1 heat-shrink tubing that is 2 mm in diameter.
    • You can use this method to repair any type of electrical cable with exposed wires. Heat-shrink tubing can be used to repair long sections of exposed electrical wire as well.
    • Examples of cables you can apply heat-shrink tubing to are vehicle wires or home appliance power cords.
  2. 2
    Cut the heat-shrink tubing to at least twice as long as the damaged area. Measure the damaged area and double the measurement. Measure out this length on your heat-shrink tubing and cut the tubing using scissors.[10]
    • The tubing will be about 10-15% shorter after you shrink it, so cutting it twice as long as the damaged area ensures it will cover the exposed wire and some of the cable on either side of the exposed section to prevent further damage.
  3. 3
    Slide the heat-shrink tubing over the damaged spot. Slip the tubing over the end of the cable and center it over the exposed wire. This will ensure it covers the damaged area and an equal amount of the undamaged cable on either side of it to reinforce the area.[11]
    • Note that heat-shrink tubing won’t work for cables that have ends that are larger than the cable itself, like chargers, because you won’t be able to get the tubing over the large ends. This method works best if the electrical cable has 1 end that is the same diameter as the cable itself.
  4. 4
    Heat the tubing using a heat gun or hair dryer until it shrinks. Turn a heat gun or a hair dryer on to high heat and hold the tip within about 1 cm (0.39 in) of the tubing. Wave the heat gun or hair dryer back and forth along the entire length of the heat-shrink tubing until it shrinks tightly around the cable.[12]
    • This will stiffen the damaged area and protect the exposed wire to prevent further wear and tear.
    • The tubing will start to shrink almost right away. Depending on how long the section of heat-shrink tubing you are heating up is, you will probably be able to shrink the whole piece in 30 seconds or less.
    • Don’t ever use an open flame to shrink heat-shrink tubing because you can easily just melt it and damage your cable even more.
  5. Advertisement

Expert Q&A

  • Question
    How can I tell if an outlet is grounded before working on an exposed wire?
    Jesse Kuhlman
    Jesse Kuhlman
    Master Electrician
    Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electrician Services based in Massachusetts. Jesse specializes in all aspects of home/residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.
    Jesse Kuhlman
    Master Electrician
    Expert Answer
    You'd need a three prong tester. You just plug it into the outlet and a set of LED lights will turn on to indicate whether it's grounded or not. You can also use a multimeter if you prefer.
  • Question
    What can I use to attach two exposed wires?
    Jesse Kuhlman
    Jesse Kuhlman
    Master Electrician
    Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electrician Services based in Massachusetts. Jesse specializes in all aspects of home/residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.
    Jesse Kuhlman
    Master Electrician
    Expert Answer
    Wire caps are the post popular option. Those are the little, plastic, thimble-shaped caps that you twist on top of two wires to connect them. You can also use a butt splice, which is a little plastic joiner.
  • Question
    Can a multimeter measure wattage?
    Jesse Kuhlman
    Jesse Kuhlman
    Master Electrician
    Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electrician Services based in Massachusetts. Jesse specializes in all aspects of home/residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.
    Jesse Kuhlman
    Master Electrician
    Expert Answer
    No, if you're running wires or doing any kind of electrical work, you can't use a multimeter to measure wattage. You can use it measure amperage and voltage, though!
Advertisement

Warnings

  • If you leave electrical wire exposed, the wire itself can start to fray, which can eventually result in a faulty or completely broken wire.
    ⧼thumbs_response⧽
  • Don’t try any of these methods to fix exposed electrical wires that are completely bare. Replace them instead.
    ⧼thumbs_response⧽
  • Avoid buying laptop chargers made by third party manufacturers, which can damage your laptop. Always buy a replacement cable from your laptop’s manufacturer.
    ⧼thumbs_response⧽
Advertisement

Things You’ll Need

Wrapping Minor Damage with Electrical Tape

  • Electrical tape
  • Scissors (optional)

Repairing Charger Cables with Sugru

  • Packet of Sugru

Applying Heat-Shrink Tubing to Electrical Wires

  • Heat gun or hair dryer
  • Heat-shrink tubing
  • Scissors

About This Article

Jesse Kuhlman
Co-authored by:
Master Electrician
This article was co-authored by Jesse Kuhlman. Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electrician Services based in Massachusetts. Jesse specializes in all aspects of home/residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes. This article has been viewed 90,387 times.
9 votes - 78%
Co-authors: 4
Updated: January 16, 2023
Views: 90,387
Advertisement