A biscuit joiner, also known as a plate joiner, is an electric woodworking tool. It joins two pieces of wood together without staples, nails, or screws. A biscuit joiner uses a small blade (4 inches or 101.6 millimeters) to cut a crescent shaped hole in the opposite edges of two pieces of wood. An oval wooden "biscuit" is covered with glue, placed in the slot, and the two boards are clamped together to form a joint. This simple process creates tight, smooth, and seamless joints. To get the results you want in woodworking, you need to know how to use a biscuit joiner.

Steps

  1. 1
    Align the pieces of wood you want to join.
  2. 2
    Make marks at the places where biscuits will be placed.
    • Use as many biscuits as needed to secure the pieces of wood.
    Advertisement
  3. 3
    Mark the other piece of wood at the same locations.
    • The biscuit process allows some leeway in aligning the pieces of wood, so perfect alignment is unnecessary.
  4. 4
    Use the settings and stops on the biscuit joiner to set the depth of the cut.
  5. 5
    Place the joiner firmly on the pencil markings.
  6. 6
    Turn on the joiner and push it forward to cut a crescent shape into the wood.
    • Apply pressure to release the blade, allowing it to cut the wood.
    • The joiner's cutting blade will retract while it is idle.
    • The crescent shaped slots may be longer and larger the joiner biscuit; this allows a user to better align the joined pieces just before the glued joiner biscuit starts to set.
  7. 7
    Cut slots at each location on each piece of wood.
  8. 8
    Cover each biscuit with wet wood glue or apply glue inside the slots.
  9. 9
    Slip a biscuit into each one of the slots at each location.
  10. 10
    Clamp the two pieces of wood firmly with wood clamps.
    • Upon being clamped, the compressed biscuit will expand to fill the crescent shaped slot and create a strong bond between the two pieces as it dries.
  11. 11
    Wipe away any excess glue before it dries.
  12. 12
    Clean the joiner according to product directions before storing when not in use.
  13. Advertisement

Warnings

  • If the joiner is burning or smoking the wood in the slots, it is time to sharpen or replace the blade.
    ⧼thumbs_response⧽
  • Wear goggles and a dust mask when working with a biscuit joiner.
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Wood glue
  • Wood clamps
  • Biscuits come in three sizes:
  1. 0 - 5/8 inch wide x 1-3/4 inches long (13 mm x 44.45 mm); #10 - 3/4 inch wide x 2-1/8 inches long (19.05 mm x 2 mm); #20–1 inch (50.8–2.5 cm) wide x 2-3/8 inches long (25.4 mm x 2.38 mm). Biscuits are .148 inches (3.76 mm) thick.

You Might Also Like

Remove a Stuck BoltRemove a Stuck Bolt
Video Player is loading.
Current Time 0:00
Duration -:-
Loaded: 0%
Stream Type LIVE
Remaining Time -:-
 
1x
Remove a Broken Bolt
Calibrate a Torque WrenchCalibrate a Torque Wrench
Make Velcro Stick AgainMake Velcro Stick Again
Open Cable TiesOpen Cable Ties
Use a Torque WrenchUse a Torque Wrench
Use Lock WashersUse Lock Washers
Remove RivetsRemove Rivets
Hang Something on BrickHang Something on Brick
Video Player is loading.
Current Time 0:00
Duration -:-
Loaded: 0%
Stream Type LIVE
Remaining Time -:-
 
1x
Fill Nail Holes
Load a Packing Tape DispenserLoad a Packing Tape Dispenser
Video Player is loading.
Current Time 0:00
Duration -:-
Loaded: 0%
Stream Type LIVE
Remaining Time -:-
 
1x
Make a Rubber Band Ball
Video Player is loading.
Current Time 0:00
Duration -:-
Loaded: 0%
Stream Type LIVE
Remaining Time -:-
 
1x
Apply Velcro Strips
Measure a BoltMeasure a Bolt
Advertisement

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed 37,966 times.
51 votes - 96%
Co-authors: 7
Updated: April 11, 2019
Views: 37,966
Advertisement