The Canon A-1 is a legendary, hugely influential and (for its time) extremely sophisticated late-70s manual focus camera that, like many other 35mm cameras, can be bought extremely cheaply, and gives superb results. If you've bought or inherited one, you may find using one to be a little daunting if you're used to fully-automatic point-and-shoot digital cameras. These simplified instructions will guide you through the basics of setting up and using an A-1.

Method 1
Method 1 of 3:

Basic Preparation

  1. 1
    Fit your lens if you haven't already. The steps below describe how to fit original FD lenses with a silver locking ring, the kind which were typically sold with the camera at the time. If yours doesn't have this, it's a late-70s-and-onwards "new FD" lens, and the instructions will differ somewhat; in the instructions below, replace the part with twisting the silver locking ring with twisting the whole lens itself until it audibly locks into place.
  2. 2
    Turn the camera on. Rotate the main switch from "L" to "A". Canon's manual recommends leaving this at "L" when you're not using the camera to conserve battery life. It might not be worth bothering with this, especially if you're not using one of Canon's power winders for the A-1; just handle your camera carefully (so as not to hit the shutter button) and you'll be okay.
    Advertisement
  3. 3
    Turn on your viewfinder display. This is a small lever right next to the large ASA dial on the left of the camera (if you're looking from the back). Turn it clockwise to uncover the white dot. This will turn on the display in your viewfinder (and you want this).
  4. 4
    Open your viewfinder blind. Uncommonly, the A-1 has a blind on the viewfinder to stop stray light entering the viewfinder on long, tripod-mounted exposures. It's a neat enough feature, but most of the time, you will not need this. If it hasn't been done already, turn the small lever to the left of the viewfinder window clockwise to open the blind.
  5. 5
    Check your battery. The A-1 is an electronically controlled camera that will not work with a low or dead battery; the shutter will refuse to fire if it is. Press the battery test button (illustrated). If the LED next to the shutter button doesn't blink at all then your battery is dead. If it does not blink very rapidly (several times per second), then it's low, and you should replace it. Pick up a few cheap 4LR44 (aka A544) cells and replace them.
  6. 6
    Load your film. This is just like any other rear-loading SLR.
    1. Pull your film rewind knob upwards to open the back of the camera.
    2. Place your film in the film chamber, and draw the leader of the film over to sit in one of the slots, and so that the bottom of the leader is engaging the film transport sprocket.
    3. Close the back of the camera, push the shutter and then wind the film on. Repeat until the frame counter shows that you're on the first frame. While you do that, watch the rewind knob on the left as you wind the film on on; this should turn as you wind it on, and if it doesn't it probably means your film isn't loaded correctly.
  7. 7
    Set your film speed. This is necessary for automatic exposure to work accurately. The film speed dial sits around the rewind crank, and has a silver unlocking button on the side, as illustrated. Push this in, and then rotate the dial to the same as the ASA (same as the ISO) speed rating of your film.
  8. 8
    Set your lens' aperture ring to "A". This will allow the aperture to be set by the camera; for the most part, this is what you want (it always is, unless you're doing fully manual exposures for some reason).
  9. 9
    Get up and get out there and take some photographs. The next part of this guide will walk you through using the A-1.
  10. Advertisement
Method 2
Method 2 of 3:

Taking Photographs with the A-1

  1. 1
    Uncover your AT dial. This is a cover for the dial which sets your shutter speed or aperture. Slide it down to uncover the dial. This is the single most important control on the camera, so play with the dial a little to get the feel of it. ("AT dial" is a hideous term from Canon's literature, borrowed here for lack of a better one, sorry.)
  2. 2
    Set your exposure mode. The A-1 has three modes that you'll be interested in: fully-programmed AE (which is fully automatic), shutter-priority AE, aperture-priority AE and fully manual.

  3. 3
    Look through the viewfinder and very gently half-press the shutter button. Your shutter speed and your aperture (either the shutter or the aperture or both or none could be automatically selected) will be displayed in the viewfinder. If either the shutter speed or aperture readouts are blinking, it means you've selected a shutter speed that is either too fast or slow for the largest or smallest apertures on your camera, or an aperture that requires a shutter speed faster or slower than the camera has available.[2] Select a different aperture or shutter speed if this is the case.
  4. 4
    Focus. The A-1 provides you with two useful focusing aids to ensure that your shots are sharp. One is a split image, right in the center, which splits the images into two pieces, which are aligned when the image is in focus.

    The other (more useful) aid is a microprism ring around the outside of the split screen. this will cause any defocus to be far more obvious than it would be otherwise; when it's out of focus, this area will flicker and display a very obvious "cross-hatched" pattern. Turn the focus ring until either the split image is no longer visibly split, or until the image in the microprism ring is visibly sharp.
  5. 5
    Set exposure compensation, if required. This feature of the A-1 forces the camera to either under- or over-expose your shot by a given amount. You'll need this in tricky, inconsistent lighting conditions. Press the button to unlock the exposure compensation dial and turn it to give you the desired amount (you can do this in 1/3 stop increments). Turning this clockwise will give you underexposure, and counter-clockwise will give you overexposure.

    Actually, the A-1's exposure compensation dial is annoying and difficult to do one-handed, so you might not want to bother with this. The ASA dial, on the other hand, can be changed with a fingertip. Neither the ASA nor exposure compensation dials will give you any indication (other than by looking at them) that you're forcibly over- or under-exposing, and the ASA dial has the advantage of being much easier to use. It's up to you.
  6. 6
    Press your shutter button. The viewfinder will temporarily blank out and the shutter will fire. If you're using one of the optional power winders, the film will advance itself to the next frame, otherwise, wind it on yourself.

    Keep photographing until you get to the last frame. Don't pay any attention to the frame counter; you're only at the end of the roll when the winder becomes difficult-to-impossible to wind on (don't force it!), or when your power winder (if you have one) refuses to wind it on any further.
  7. Advertisement
Method 3
Method 3 of 3:

Unloading your film

  1. 1
    Press the rewind release button on the base of the camera.
  2. 2
    Flip out the rewind lever on the rewind knob and turn it clockwise to wind the film back into its canister. The frame indicator will go backwards as you wind. Keep winding until the rewind lever goes very stiff, and then suddenly turns much more freely. When the latter happens, this means your film is free of the transport sprocket. Wind it in a bit further if you like.
  3. 3
    Open the back of the camera by lifting the rewind knob upwards. The back of the camera will spring open. Remove your film and get it developed. Load in another roll and carry on enjoying this superb classic camera!
  4. Advertisement

Community Q&A

  • Question
    I bough a Canon A-1 off of Ebay, it looks to be in good condition except the Negative Battery Terminal has some corrosion and the terminal is stuck. Can this be fixed?
    Community Answer
    Community Answer
    Scrub the negative terminal gently with a flat-head screwdriver until it is clean.
  • Question
    How do I charge the battery?
    Community Answer
    Community Answer
    The battery is not chargeable, so you have to replace it. The battery lasts anywhere from 6-18 months depending on usage so you don´t need to replace it often.
  • Question
    Every time I load film, my Canon A-1 takes a picture automatically. How do I stop it from doing this?
    Community Answer
    Community Answer
    The first few exposures on the film are "blank," so that when you load your film you are not wrecking any possible exposures by doing it in open light. When you put your film in and close the back, you would usually take a photo and wind it so that you can get past those blank exposures. The A-1 does this automatically.
Advertisement

References

  1. The A-1's meter will be functional down to EV -2, according to this page, which is several stops dimmer than a typical night street scene.
  2. As before, it could also mean that you're trying to take a photo in light levels that are outside of the A-1's metering range, which is a somewhat less common situation.

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 18 people, some anonymous, worked to edit and improve it over time. This article has been viewed 351,603 times.
275 votes - 94%
Co-authors: 18
Updated: February 16, 2022
Views: 351,603
Advertisement