The increasing use of surveillance cameras in response to concerns about terrorism means that when you're in public, there's a chance you're being watched and recorded.[1] [2] While such security measures make some people feel safe, others worry about the implications of being watched by "Big Brother." By embedding a hat with high-brightness infrared (IR) LEDs, you can obstruct your face from being recorded by any kind of hidden, security, paparazzi, or personal video camera. To do so, follow these instructions.

Steps

  1. 1
    Wire the LEDs. Make sure your wires are long enough (around 15cm / 6 in each) depending on how big your hat is. Start wiring up the LEDs one by one, making sure to note the positive and negative terminals. (Color-coding the wires is highly recommended: for example, you can use a white wire for each positive terminal and a color wires for each negative terminal.) Wrap the wires tightly to each LED so they won't fall apart. You can even solder the connections, though it's probably not necessary.
  2. 2
    Mark and cut the hat. This part is also crucial, as you need to pick logical (but inconspicuous) spots to place the LEDs: if you place them too far apart from each other, the light beam won't be strong enough to blind a camera, but if you place them too close, they will hide your face from a certain angle but not others. Think this out and position them well. Mark each spot with a marker, then cut a few holes with a pair of small scissors in the middle of the front of the hat as well as a few on the sides.
    Advertisement
  3. 3
    Attach the LEDs. Turn the hat inside out. Take each LED and place it tight in its hole. For extra stability, secure each LED with a dab of glue so that it won't fall out; however, try not to cover the bulb, focusing instead on holding the wire in place. Hot glue will work well for this purpose. When you’re done, flip the hat right-side-out.
  4. 4
    Secure wires with tape. Tape all the wires together using electrical tape and secure them to the inside of the hat.
  5. 5
    Power up. Connect a small 9v battery to the wires and secure it with electrical tape. (This is where having color-coded wires will really come in handy, as they will tell you which wires to connect to the positive and negative terminal of the battery.) You can even add a little on/off switch if you want. In this example, the battery is placed on the inside back of the hat.
  6. 6
    Finished.
  7. Advertisement

Warnings

  • This works about as well as shining a light in someone’s face – except CCTV never blinks. Thus, it requires one to be able to continually face the camera at the right angle. (Notice almost half of the face is visible in the photo despite good positioning.)
    ⧼thumbs_response⧽
  • This method works best in lower light conditions; in full daylight or brightly lit areas, there is less of a light discrepancy, making the LEDs less blinding to the camera. (This can be seen in the video when the finished product is shown: you can clearly see the hat and the individual LEDs, with no blinding effect.)
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Though approximate prices are given, this project should cost about $11 USD.
  • 8 or more high-intensity, infra-red LEDs ($0.30 apiece; $2.40 total)
  • A hat/cap ($6.00 if you don’t have one already)
    • make sure it can accommodate all the interior parts
    • choose one with a design that will camouflage the LEDs
  • 16 thin wires from a 2-meter long UTP cable ($1.00)
  • Electrical tape ($0.80)
  • A 9v battery ($1.00)

References

  1. Boston News on surveillance
  2. USA Today on surveillance
  3. Instructables - Original source, shared with permission.

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 24 people, some anonymous, worked to edit and improve it over time. This article has been viewed 347,425 times.
72 votes - 61%
Co-authors: 24
Updated: February 5, 2021
Views: 347,425
Advertisement