How to Install a Car Stereo

A simple step-by-step guide to replacing your car stereo

Installing a new car stereo can often be simple enough to do yourself, and this article will provide you with a general guide on how to do it. Keep in mind that some cars and systems are more complicated than others and that every car and stereo system will be different, so some specifics may vary. Be sure to read any instructions that come with the new car stereo before attempting to install it.

Part 1
Part 1 of 3:

How to Take Out the Old Stereo

  1. Image titled Install a Car Stereo Step 1
    1
    Set the parking brake and disconnect the negative cable from your car battery. Be sure to do this to avoid short-circuiting the electrical system during the installation, which could lead to fire or physical harm for you.[1]
  2. Image titled Install a Car Stereo Step 2
    2
    Unscrew any screws that are securing the trim in place. Be careful to remove all screws before trying to pry off the trim or you may break it.[2]
    Advertisement
  3. Image titled Install a Car Stereo Step 3
    3
    Remove the trim. For some cars, you may need to remove several pieces of plastic trim, usually working from the bottom up.[3]
    • If you need to remove trim that includes any knobs or drawers, remove them before trying to pry off the trim.
    • Use your hands or a pry tool to pry off each piece of trim. Pry tools are specifically for this purpose and will not damage the trim pieces.
  4. Image titled Install a Car Stereo Step 4
    4
    Pull out any necessary components. If you need to remove any components before being able to access the stereo, do so.
    • Disconnect components that are wired to the car. Take a picture of how each is wired for later reference.
  5. Image titled Install a Car Stereo Step 5
    5
    Loosen the stereo. Different cars may have varying elements securing the stereo in place.
    • If the stereo is held in place by screws or nuts, loosen them with the appropriate tool (screwdriver or nutdriver, respectively).
    • If the stereo isn't held in place by screws or nuts, you'll need to use a radio-removal key. This tool is commonly necessary in Ford vehicles. Radio-removal keys (sometimes also referred to as radio-removal tools) will typically either be in an elongated horseshoe shape or will have a circular shape at one end and a notched shaft at the other. They’re available at most auto-parts stores.
    • Insert the keys into the two small slots in the face of the stereo. You will release a mechanism holding the stereo in place. Slide the radio-removal keys into each slot again until you feel the stereo loosen from in its housing. You should then be able to pull out the stereo relatively easily.
  6. Image titled Install a Car Stereo Step 6
    6
    Pull the stereo out of the panel. You may want to use needle-nose pliers to grip the edge of the stereo and help you pull it out.[4] Pull it gently, and if the stereo doesn't come out easily, double check that you haven't missed any components that may be holding it in place.
  7. Image titled Install a Car Stereo Step 7
    7
    Take a picture of how the stereo is wired. This is an important step because the photo will serve as a reference later when you’re wiring in the new stereo.
  8. Image titled Install a Car Stereo Step 8
    8
    Unplug the stereo connections. You’ll see a series of wires connected to the back of the stereo, and you’ll need to disconnect each of them.
    • First unplug the antenna wire, which will typically be a thicker wire plugged in separately from the rest. Once it’s unplugged, you should be able to move the stereo around more freely.
    • Next unplug the each of the wire harness connectors. There will typically be several of these and you can recognize them because a series of wires will feed into each one. The plastic piece into which the wires are fed should have either a tab or a button you can push, which will release the harness.
    9. Advertisement
Part 2
Part 2 of 3:

How to Install the New Stereo

  1. Image titled Install a Car Stereo Step 9
    1
    Match up the wires. Match the wires of the car’s harnesses to the new stereo’s harnesses. Each harness connector is unique, so it should be easy to figure out which ones fit together.[5]
    • To be safe, check the wiring diagrams for both your car and the new stereo to verify you’ve connected them correctly.
    • If your car's stereo doesn’t use wire harnesses, you’ll need to match up each wire manually. The wires are color-coded; however, the wires on an after-market stereo may not match with the color-coded wires in your vehicle. It's best to study and follow the wiring diagram that came with the stereo.
    • Connect the matched wires. There are two options for connecting the wires, crimping or soldering. Crimping is faster and easier, but soldering will provide a more stable and secure connection. Be sure to use the proper size crimper and don’t try to bundle the wires with tape — it will eventually dry out and fall off. Bundle wires using zip ties instead.[6]
  2. Image titled Install a Car Stereo Step 10
    2
    Assemble the mounting kit. If your new stereo came with a separate mounting kit, assemble it according to the stereo's instructions (it will often mean fitting a metal housing sleeve into the mounting frame).
    • Push down on the tabs located around the metal sleeve with a screwdriver to secure the metal sleeve in place.
  3. Image titled Install a Car Stereo Step 11
    3
    Connect the power source. Typically, if you have a wiring harness, this connection will be made when you connect the new stereo harnesses to the harnesses in the car.
    • If you aren't using a wiring harnesses, you’ll need to manually connect the power. Determine whether your car has a switched power source (typically a red wire) or a constant power source (typically a yellow wire). Some vehicles even have both types of power sources. For more information on switched versus constant power, go here.
  4. Image titled Install a Car Stereo Step 12
    4
    Ground the stereo. If you're using wiring harnesses, this connection will be made when you connect the harness pieces.
    • If you aren't using a wiring harness, you'll need to locate the bolt, wire, or screw that connects with the car's bare metal chassis. Loosen the bolt, wire, or screw and slip the stereo's ground wire (usually black) underneath, then tighten.
    • Note that the ground connection is important to the optimal performance of the stereo. If the ground wire doesn't connect to the bare metal, it won't work. And if the ground wire connection is loose, it could result in poor audio output. Sand down the area with sand paper to ensure a good connection.
  5. Image titled Install a Car Stereo Step 13
    5
    Connect the remaining wires. Plug in the antenna cable and connect the stereo's wiring adapter to the the car's wire harness. Connect the output converter if one is needed to make the new stereo compatible with the car's audio system. Have in mind that all wires should be connected in the end and there should no single one hanging unattended.
  6. Image titled Install a Car Stereo Step 14
    6
    Test the stereo. Turn the power on and test the AM, FM, and CD components. Test the fade and balance settings to be sure the speakers are working properly. Turn the power back off.
    7. Advertisement
Part 3
Part 3 of 3:

How to Finish the Installation

  1. Image titled Install a Car Stereo Step 15
    1
    Push the stereo into place. When the stereo is fully in, you should hear it click into place.
  2. Image titled Install a Car Stereo Step 16
    2
    Reconnect the components. Fasten in any screws that are needed to hold the stereo in place, reconnect any wired components, and replace any knobs or drawers that were removed.
  3. Image titled Install a Car Stereo Step 17
    3
    Snap all the pieces of trim back into place over the stereo. Double check that all screws and trim pieces are securely in place.
  4. Image titled Install a Car Stereo Step 18
    4
    Try out the new stereo. Turn the car power on again and play around with the stereo and its settings to be sure everything is in working order.
    5. Advertisement

Community Q&A

  • Question
    How do I replace a 1996 Jeep radio with a Pioneer radio by matching the wires manually?
    Community Answer
    Community Answer
    It should be red to green, orange to purple, maroon to turquoise, pink to silver, and clear to black.
  • Question
    How do I connect the stereo to the equalizer if the stereo has no input port?
    Community Answer
    Community Answer
    You have to buy an adapter cable. If you buy from a store like Radio Shack, you may be able to get the salesman to come outside and help you install it... For free!
  • Question
    If I have an aftermarket Pioneer radio, and want to replace it with another Pioneer radio, do I need a new wiring harness?
    Community Answer
    Community Answer
    Not necessarily, just compare the harnesses and once they match, you can go ahead.
Advertisement

Warnings

  • Follow the specific instructions provided with the new stereo. Some of the installation steps may be specific to your car and stereo.
    ⧼thumbs_response⧽
  • If you find yourself feeling lost or frustrated, get help from a professional — otherwise you may damage the car or hurt yourself.
    ⧼thumbs_response⧽
Advertisement

Things You’ll Need

  • A car with a stereo system
  • A new stereo
  • Phillips and flat head screwdrivers (depending on model)
  • Nutdriver (depending on model)
  • Radio-removal keys (depending on model)
  • Pry tool (optional)
  • Needle nose pliers (optional)
  • Zip ties
  • Electrical tape
  • Soldering gun or crimp connectors


You Might Also Like

Remove a Stuck CD from a Car CD Player
How to
Remove a Stuck CD from a Car CD Player
Install SubwoofersHow to Install a Subwoofer
Unlock Your Locked GM Theftlock Radio
How to
Unlock Your Locked GM Theftlock Radio
Wire a Car Stereo
How to
Wire a Car Stereo
Hook Up an iPhone to a Car Stereo
How to
Hook Up an iPhone to a Car Stereo
Improve Car Radio Reception
How to
Improve Car Radio Reception
Remove an Old Car Stereo
How to
Remove an Old Car Stereo
Connect a Car Stereo for House Use With a Psu
How to
Connect a Car Stereo for House Use With a Psu
How to
Install a Basic Aftermarket Car Stereo
Sound Deaden Your Car
How to
Sound Deaden Your Car
Install a Multiple Component Car Audio System
How to
Install a Multiple Component Car Audio System
Install A Car Radio Head Unit
How to
Install A Car Radio Head Unit
Install Sub Woofers
How to
Install Sub Woofers
Upgrade Your Car's Sound System
How to
Upgrade Your Car's Sound System
Advertisement

References

  1. ↑ https://www.youtube.com/watch?v=sXmcOjXKzmY
  2. ↑ https://www.youtube.com/watch?v=sXmcOjXKzmY
  3. ↑ https://www.crutchfield.com/S-bZlpyfJL6BC/learn/learningcenter/car/car_stereo/installation_guide.html
  4. ↑ https://www.youtube.com/watch?v=QHYRj9ofIVc
  5. ↑ https://www.popularmechanics.com/technology/audio/how-to/a770/3380301/
  6. ↑ http://www.crutchfield.com/S-vdeoFoldTKL/learn/learningcenter/car/car_stereo/installation_guide.html

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 61 people, some anonymous, worked to edit and improve it over time. This article has been viewed 1,109,277 times.
How helpful is this?
Co-authors: 61
Updated: March 19, 2023
Views: 1,109,277
Categories: Car Radios and Sound Systems
Article SummaryX

To install a car stereo, match the wires of the car’s harnesses to the new stereo’s harnesses. Each harness connector is unique, so it should be easy to figure out which ones fit together, but you can check the wiring diagrams for your car and your new stereo if you’re not sure. If your car’s stereo doesn’t use wire harnesses, you’ll need to match up each wire individually. Assemble the mounting kit if your stereo came with one, then slide the stereo into place and fasten any screws that are needed to hold the stereo in place. Keep reading to learn how to take out your original stereo!

Did this summary help you?
Advertisement