How to Remove Grout and Cement Spots off Ceramic Tiles

Last Updated: May 6, 2021

Have you got extra grout marks or tile adhesive spots on your recently renovated bathroom? If so try these tips for removing them. If it is a just a few spots and your floor tiles have a good hard surface that won't scratch easily, cleaning tiles like this should be easy.

Steps

1
Assemble cleaning tools. For the first steps, you only need a steel scourer pad and something to scrape with, such as a screwdriver. For harder stains, you will need to resort to a professional response using acid. See "Things You'll Need".^{[1]
X
Research source}
2
Try rubbing the tiles with a stainless steel scourer pad.^{[2]
X
Research source}

Advertisement
3
Scrape off. If you still have a few larger lumps try scraping with a blunt screwdriver to get the worst off and then the scourer.
4
Try intermediate measures if the above steps don't do the job. A grout haze remover may be of use. You can find this at a home store or tile shop. Follow the instructions on the container. You can use the stainless steel scouring pad as above, or you may try a man made scouring pad.^{[3]
X
Research source}
5
Try advanced measures if the above steps don't do the job. If you have a lot of hard grout or tile adhesive on them, cleaning tiles like this calls for extreme measures. Tilers use diluted Hydrochloric acid as a last resort; it is also known as Muriatic acid. This acid eats at the cement base of the product you are trying to shift. It is important to read the warnings in detail before proceeding - cleaning tiles with acid must to be done in a responsible way:^{[4]
X
Research source}
- Use a very small spot at a time and observe how it goes. This is important, as doing a small section at a time, you will be working safely and in control. Use a small bristle brush and dab a spot on at a time. When the bubbling stops wash it off with water, and try the spot with your scourer again and with a bit of luck it will come off easily.
- Repeat the process as needed.
- Wash clean and wash again, get rid of all traces of the acid.

Community Q&A

Question

How do I clean hardwood flooring?

Adriana Lima

Community Answer

I myself would use a steam mop, which cleans with steam not water. But first check with the floor manufacturer (look up their number online) to be sure it will not damage the floor.

Warnings

Always pour the acid into the water; if done the other way around, the larger volume of acid reacts violently to the first few drops of water and splashes of it could go everywhere.

⧼thumbs_response⧽
Helpful 7 Not Helpful 4
Check the dilution rate on the bottle or get advice from someone who knows, because you could have any strength of acid. It is sold usually at around 30% dilution and 70% dilution. Dilute a very small amount of the 30% stuff 3 to 1 for a small trial section. If used neat, it can melt the bristles of a brush within a few minutes.

⧼thumbs_response⧽
Helpful 9 Not Helpful 8
Dilute the acid outside in the fresh air.

⧼thumbs_response⧽
Helpful 6 Not Helpful 6
Wear protection, for eyes, breathing and rubber gloves and old clothes and boots.

⧼thumbs_response⧽
Helpful 2 Not Helpful 7
Open the doors, windows, extractor fan if you have got one, to give you ventilation. The fumes are dangerous. There is (or should be) a chemical reaction going on between the cement and the acid; you will see the surface of the grout spots bubbling of fizzing.^{[5]
X
Research source}

⧼thumbs_response⧽
Helpful 0 Not Helpful 0
Wear the normal safety gear that you would use when handling harsh chemicals. Rubber gloves and eye protection are a must.^{[6]
X
Research source}

⧼thumbs_response⧽
Helpful 0 Not Helpful 0