How to Make a Fork Bracelet

Last Updated: October 10, 2022

Making silverware jewelry is a fun and creative way to repurpose old utensils into unique fashion statements. Constructing a bracelet out of a fork is very easy, and you can find some forks for less than a dollar! Making fork bracelets are an ideal project for any crafter looking for a new jewelry project.

Part 1

Part 1 of 2:

Bending The Body of The Fork

1
Choose your fork. Look to buy forks at garage sales or thrift stores. Usually, silverware sold at garage sales and thrift stores are relatively cheap. The fork that you buy also needs to be made of silver or sterling silver.

That’s because silver and sterling silver is very easy to manipulate and bend. Forks that are silver or sterling silver will have the numbers “900” or “925” stamped on the back of the fork.^{[1]
X
Research source}

Consider looking for forks that have decorative detailing on the handle. It can add some flair when you wear it as a bracelet.

Because stainless steel is less pliable, avoid using stainless steel forks to make your bracelet.^{[2]
X
Research source}
2
Bend the fork with your hands. Use your hands to bend the fork following the natural curve of the back of the fork (the curves area around the base of the fork tines).^{[3]
X
Research source} Position the fork upside down, with the face of the fork turned toward the ground.

Grip one hand over the root and tines of the fork, and position your other hand on the end handle of the fork. With the hand that is gripping the end of the fork, extend your thumb out to the neck of the fork, so it can act as a fulcrum while you bend.^{[4]
X
Research source}

Apply pressure to bend and curve the front portion of the fork (with the tines) downward. Once the root and tines are bent, slide your hands down the body of the fork, bending the handle little by little.

When you are finished bending the fork with your hands, the fork should be bent into a relatively even “U” shape.

Advertisement
3
Secure the end of the fork. Use an adjustable wrench to hold steady the end of the fork as you bend the body of the fork with pliers.^{[5]
X
Research source} Twist the adjustable screw on the head of the wrench to open up the wrench jaws. Position the end of the fork between the jaws of the wrench, placing the fork on the stationary top jaw.
- Twist the adjusting screw to raise the lower jaw of the wrench, and clamp down tightly on the fork’s end.
4
Wrap the fork with a protective material. Wrap the end portion of the fork with a small square of thick cloth material like corduroy or denim. The cloth can be as small as a square inch, it just has to completely surround and cover both the top and bottom surfaces of the fork.

This is so the pliers don’t leave small indents in the body of the fork as your grip and bend it.

Hold the protective cloth in place with a couple fingers of the hand that is gripping the adjustable wrench, so you can pick up the pliers with your free hand.
5
Bend the body of the fork. Position the wrapped end area of the fork in between the open pinchers of the needle nose pliers. Squeeze together the handles of the pliers to clamp down the pinchers on the wrapped portion of the body of the fork closest to the tines of the fork.^{[6]
X
Research source}

Firmly grip the adjustable wrench, and apply force to turn the needle nose pliers down, bending the body of the fork.

Each bend you make, slide the protective material and the pliers down toward the end of the fork (toward the wrench) and keep making little bends.^{[7]
X
Research source}

When you are finished bending with the pliers, the body of the fork should look rounded instead of the “U” shape from earlier.

Part 2

Part 2 of 2:

Bending The Fork Tines

1
Curve the fork tines. Once the body has been bent into a rounder shape, loosen and remove the adjustable wrench from the end of the fork. Wrap the tines of the fork with the protective material, and use the same needle nose pliers to clamp down over the protective material.

Position the pliers so they clamp down on two of the four fork tines. While one hand is holding the body of the fork, use downward pressure to bend two tines at a tine, following the natural curve of the fork tines.^{[8]
X
Research source}

Once you curve two tines into a rounder shape, flip the fork to the other side, clamp the pliers down, and bend the other two tines.

Be sure to make your tine bends smooth and even. You can adjust and move the pliers in small increments to bend the tines at different points, but try to avoid making choppy and rough bends in the tines.^{[9]
X
Research source}
2
Roll the outer fork tines. Use the tip of your jewelry pliers to grip the tip of one of the outside tines of the fork. Twist the pliers laterally, to roll the tine outward until the tip of the tine is rolled and touches the outside edge of the tine. Do this on both outside fork tines.
3
Roll one of the inner fork tines. Use the tip of the jewelry pliers to grip the tip of one of the inner fork tines. Twist the pliers to roll the tine back on it self, rolling in the opposite direction of the curve of the bracelet and the natural curve of the tines.^{[10]
X
Research source}

Roll the tine all the way down to the root of the tines. Release the small jewelry pliers and grip the needle nose pliers along the sides rolled up tine (the pliers should be parallel with the rest of the fork tines).

Twist the roll to the side, so it’s perpendicular to the fork tines. Then bend down the rolled tine so it can lay flat on the back of the fork root.

The rolled tine will most likely not be completely flesh against the fork root, so use the needle nose pliers to clamp down on the rolled tine, and press it flat against the fork root.^{[11]
X
Research source}
4
Curve the other inner fork tine. In the same manner you rolled the outer fork tines to the sides until the tips met the edges of the tines, roll back the tip of the other inner fork tine.

Grip the inner tine with the small jewelry pliers, and twist the pliers to roll the tine back on itself, moving in the opposite direction of the natural curve of the tines.^{[12]
X
Research source} Roll the tip of the tine backward until the tip touches the tine again.
5
Make adjustments. Use your hands to bend the bracelet and make any adjustments to the curvature or opening of the bracelet. You can pull apart or push together the bracelet ends to modify how large you want to bracelet opening to be.