This article was co-authored by wikiHow staff writer, Hannah Madden. Hannah Madden is a writer, editor, and artist currently living in Portland, Oregon. In 2018, she graduated from Portland State University with a B.S. in Environmental Studies. Hannah enjoys writing articles about conservation, sustainability, and eco-friendly products. When she isn’t writing, you can find Hannah working on hand embroidery projects and listening to music.
There are 11 references cited in this article, which can be found at the bottom of the page.
This article has been viewed 308,197 times.
Learn more...
Many people enjoy a fizzy, carbonated drink with their meal. If you like soda but you were tired of buying cans and bottles all the time, you may have purchased a SodaStream machine. These machines can seem complicated, but as long as you insert the carbonator correctly and choose your level of fizz, you can be drinking delicious soda that you made at home in no time.
Things You Should Know
- Unscrew the cap from the carbonator and insert it into the machine. Then, screw the top of the canister into the machine.
- Fill the carbonating bottle with water. Push the carbonating block or button in short bursts to carbonate the water and remove the bottle.
- Pour a capful of SodaMix into the bottle. Screw the cap on and shake gently for 10 seconds. Enjoy your soda right away.
Steps
Putting the Carbonator in Your Soda Machine
-
1Set the soda machine on a sturdy surface, like a countertop or table. Usually, this is a table or kitchen countertop. Make sure that the surface is flat and not tilted so that your soda machine sits upright.[1]
- It will also be helpful to set up your soda machine near a sink so that you can fill up your bottle with water later.
-
2Remove the plastic seal and unscrew the cap from the carbonator. Your soda machine comes with a carbonator. This is a metal canister that says “SodaStream CO2” on it. Remove the plastic seal from the top of the canister and throw it away. Then, unscrew the plastic cap.[2]
- Always read the manual for your specific soda machine before you start setting it up.
Advertisement -
3Take off the back cover from your soda machine. The back cover of your soda machine will pop off easily. Pull it from the hole that is on the back of your machine while you hold the rest of the machine steady with your other hand. Place the cover to the side.[3]
- If you are using the SodaStream Genesis or another smaller model of the SodaStream, you will pull the top of the soda machine off instead of the back cover.
-
4Insert the carbonator into the soda machine. Place the carbonator canister into the hold where the cover was on your soda machine. Depending on the model of your SodaStream, this will either be the very back of your machine or the top.[4]
-
5Screw the top of the canister into the top of your soda machine. Turn the carbonator about 3 times in a clockwise position until it is screwed in all the way. Make sure it is held in place tightly and doesn’t wiggle around.[5]
- If you have a smaller model of the SodaStream, you will not need to screw your canister in.
-
6Replace the back cover on your soda machine. Put the cover back onto your SodaStream to lock the carbonator in place. Make sure the cover is on securely before you start using your machine.[6]
- No matter what model of SodaStream you have, make sure your cover clicks into place when you put it back on.
- Your SodaStream may have a CO2 meter that will warn you when your carbonator is running low. If it does, reset the meter each time you put in a new canister by holding down the “reset” button for 5 seconds.
Carbonating Your Water
-
1Fill up the carbonating bottle with cold water to the fill line. Your soda machine comes with a clear plastic bottle. Fill up your bottle with cold water, either from the tap or from a filter, to the fill line.[7]
- Using cold water allows you to drink your soda right away without having to chill it first.
-
2Snap or screw the bottle into the machine. Depending on which model of SodaStream that you have, you will either snap the bottle into the bottle lock or screw it into the bottle lock. To screw it in, turn it 3 times in a clockwise position. To snap it in, simply push the top of the bottle in place.[8]
-
3Push the bottle into a vertical position. Once it is locked in, gently push the bottle into a vertical position so that it is upright.[9]
- There will be a gap between the base of the machine and the bottom of the bottle.
-
4Press down the carbonating block or button in short bursts. Depending on your model of SodaStream, either press down on the entire top block of your machine or press a small black button to start the carbonation process. Press down in short bursts, taking a 1 second break in between each press.[10]
-
5Watch the LED lights that indicate how carbonated your water is. Your soda machine has 3 levels of carbonation. The first one is light fizz, the second is medium fizz, and the third is strong fizz. As you add carbonation, the LED lights will light up to indicate the levels. Decide how carbonated you want the water to be and stop pressing the button once it reaches that level.[11]
- You may have to try multiple levels of carbonation before you find the one that you like the most.
-
6Pull the bottle of water out of the lock mechanism. Once you’ve added carbonation to your water, you can pull the bottle out of your machine’s lock mechanism. Depending on your model of SodaStream, either twist the bottle or pull it out toward you to unlock it.[12]
Flavoring Your Carbonated Water
-
1Hold your bottle at a 15 degree angle and pour a capful of SodaMix in it. Choose which flavor of soda you’d like to put in your carbonated water. You can purchase different kinds of SodaMix online or anywhere that you buy SodaStream products to replicate many different flavors of soda.[13]
- Holding the bottle at an angle makes it less likely to overflow as you pour.
- Popular flavors of SodaMix include peach tea, cola, and lemon lime.
-
2Screw the cap on your bottle and shake it gently for 10 seconds. Make sure your SodaMix is mixed thoroughly by putting a cap on the bottle and shaking it gently from side to side. Don’t shake your bottle too vigorously, or you could cause it to overflow.[14]
- You can also slowly turn your bottle upside down and right side up to mix in your flavor.
-
3Enjoy your soda right after it is mixed up. You can pour your soda over ice, or simply drink it from the bottle. Your soda will be cold since you used cold water.[15]
- Store your excess soda in the fridge with the cap on for up to 2 days.
Community Q&A
-
QuestionHow far into the water does the Jet that carbonates the water bottle need to go?wikiHow Staff EditorThis answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
Staff AnswerwikiHow Staff EditorStaff AnswerIf you fill your bottle to the "Fill Line" that is labeled on the side, the jet will be able to reach the water. -
QuestionDoes the bottle have to be screwed on tightly to the SodaStream machine?wikiHow Staff EditorThis answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
Staff AnswerwikiHow Staff EditorStaff AnswerYes, your bottle should be screwed on tightly so that it doesn't wiggle around. Otherwise, your bottle could fall off. -
QuestionHow do I remove an empty canister from my SodaStream?wikiHow Staff EditorThis answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
Staff AnswerwikiHow Staff EditorStaff AnswerPop off the cover from your SodaStream and unscrew the carbonation canister in a counter-clockwise motion. This will allow you to replace your empty canister with a new one.
Warnings
- Never carbonate your water with syrup in the bottle. This will cause it to overflow and create a sticky mess.⧼thumbs_response⧽
Things You’ll Need
Putting the Carbonator in Your Soda Machine
- SodaStream machine (any model)
- CO2 canister
Carbonating Your Water
- SodaStream bottle
Flavoring Your Carbonated Water
- SodaMix (any flavor)
References
- ↑ https://www.youtube.com/watch?v=hnfywEqTR_0&feature=youtu.be&t=10
- ↑ https://www.sodastream.com.au/how-it-works/
- ↑ https://www.youtube.com/watch?v=hnfywEqTR_0&feature=youtu.be&t=23
- ↑ https://www.sodastream.com.au/how-it-works/
- ↑ https://www.youtube.com/watch?v=hnfywEqTR_0&feature=youtu.be&t=28
- ↑ https://www.youtube.com/watch?v=RrreJ_E539M&feature=youtu.be&t=52
- ↑ https://www.youtube.com/watch?v=NpBsU7h13Uw&feature=youtu.be&t=55
- ↑ https://www.youtube.com/watch?v=ubVTOPeJ6Q4&feature=youtu.be&t=17
- ↑ https://www.youtube.com/watch?v=ubVTOPeJ6Q4&feature=youtu.be&t=17
- ↑ https://www.sodastream.com.au/how-it-works/
- ↑ https://www.youtube.com/watch?v=hnfywEqTR_0&feature=youtu.be&t=87
- ↑ https://www.youtube.com/watch?v=ubVTOPeJ6Q4&feature=youtu.be&t=70
- ↑ https://www.youtube.com/watch?v=hnfywEqTR_0&feature=youtu.be&t=115
- ↑ https://www.youtube.com/watch?v=RrreJ_E539M&feature=youtu.be&t=182
- ↑ https://www.sodastream.com.au/how-it-works/
About This Article
To make soda in a SodaStream machine, you need to carbonate the water and then add flavoring. Start by removing the plastic cap from the carbonator that comes with your machine. Then, insert the carbonator into the back of your soda machine and screw the top of the canister into the top. Take the clear plastic carbonating bottle and fill it with cold water to the fill line. Attach the bottle to the lock on the front of the machine and then gently push the bottle into position so it’s upright. Press the carbonating button in short bursts to add carbonation to the bottle. Remove the bottle and pour a capful of SodaMix into it to flavor it. Screw the cap on the bottle and gently shake it for 10 seconds to fully combine it. For tips about how to watch the LED lights to indicate how carbonated the water is, keep reading!