X
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time.
This article has been viewed 70,158 times.
Learn more...
Having an air conditioning unit in your home probably means that you have a condensate pump to help remove excess water that is given off when the system is running. This helps to remove dirty water from your home so it won’t contaminate the water that you drink. If you don’t already have one or if you need to replace one, here is a guide to install one.
Steps
-
1Before installing the pump, let the air conditioner run a few cycles so that some condensate collects and to remove any oils that are left in the system.
-
2Make sure that all of the packaging is removed from the pump, and that all venting slots are clear from debris.Advertisement
-
3Set up the electrical connections. It is always important to make sure that you turn then power off at the fuse box before installing any electrical components of appliances.[1]
-
4Check the local codes to make sure you are hooking up your wires correctly.
-
5Hook up the power cord to the specified voltage.[2]
-
6Make sure it is connected to a constant power source.
-
7Check the pump for a safety switch and wire it accordingly. After all of the electrical is done, move to the next step.
-
8Connect the pump to the wall by using screws. The pump should have slots built onto the unit that will allow it to be mounted.
-
9Make sure that the pump is close to the air conditioning unit, installed below the coil drain, and that the pump unit is level. If the pump isn’t level, it will not function properly. It is also important to make sure that the unit will not spray or splash when it is running. Once the pump is mounted correctly, you are ready to pipe the unit.
-
10Use some sort of flexible tubing, if possible, as the drain pipe for the pump. This pipe should be installed so that gravity will do the work when the pump is draining the system. The inlet pipe should be on an angle where it enters the tank and should not interfere with the operation of the float valve that the pump uses.[3]
- It may also be a good idea to install a check valve somewhere on the discharge line to avoid backflow of the discharge water so it can’t be sucked back into the a/c unit. The discharge line should run into a line that goes to the city’s waste, once again to avoid contamination of fresh water.
-
11Once the pump has been installed, turn the power back on and run the a/c unit. Watch the pump and make sure that it is working correctly. Ensure that the electrical units are working correctly without sparking and that the piping is not leaking in any area.[4]
Advertisement
Community Q&A
-
QuestionWe changed the condensation pump, but now the air conditioner won't come on. What could be the problem?Community AnswerIt is probably and issue with the float valve/switch. Make sure your unit is level, then check the float to make sure it isn't sticking.
-
QuestionWhere are the yellow wires found that are connected to the condensate pump on the air conditioner?Community AnswerCut the red wire from the furnace to thermostat and connect the yellow wires to the cut ends of the red wire. This way, if the condensate pump fails the safety switch (yellow wires), it will stop the furnace/AC and no more water from condensate will be generated. If heating or AC are a must, then connect the yellow wires to an alarm.
Advertisement
References
- ↑ https://www.bhg.com/home-improvement/electrical/how-to-turn-off-power-fuse-box/
- ↑ https://www.youtube.com/watch?v=AHDlcKd0vZY
- ↑ https://www.youtube.com/watch?v=k0YdUahUXjc
- ↑ https://www.bobvila.com/articles/installing-a-condensate-pump-bob-vila-radio/
- How to wire low voltage on a condensate pump
- https://inspectapedia.com/aircond/Condensate_Pumps.php
About This Article
Advertisement