How to Bend Pipe

You can bend pipe and tubing in one of several methods, depending on what you plan to use the bent pipe or tube for. The problem in bending pipe is figuring out where and how much to bend the pipe. While many bending tools come with a set of instructions for figuring out such things as bend allowances and bend deductions, they are often written in a complex manner and assume a knowledge of mathematics that intimidates many users. While it's not possible to completely eliminate the math, it is possible to plan how to bend a piece of pipe in such a way that figuring the bending angle is simplified and so that the only math needed is simple arithmetic. The method described below is not simple, but with practice, you can master it.

Method 1
Method 1 of 3:

Selecting a Bending Tool

  1. Image titled Bend Pipe Step 1
    1
    Choose the right bending tools for your needs. There are 6 main bending methods. Each is best suited to a particular type of pipe.
    • Ram style bending, also called incremental bending, is usually used for putting large bends in light-gauge metal, such as electrical conduit. In this method, the pipe is held down at 2 external points and the ram pushes on the pipe at its central axis to bend it. Bends tend to deform into an oval shape at both the inside and outside of the bend.
    • Rotary draw bending is used to bend pipe for use as handrails or ornamental iron, as well as car chassis, roll cages, and trailer frames, as well as heavier conduit. Rotary draw bending uses 2 dies: a stationary counter-bending die and a fixed radius die to form the bend. It is used when the pipe needs to have a good finish and constant diameter throughout its length.
    • Mandrel bending is used to make stock and custom exhaust pipes, dairy tubing, and heat exchanger tubing. In addition to the dies used in rotary draw bending, mandrel bending uses a flexible support that bends with the pipe or tubing to make sure the pipe interior isn't deformed.
    • Induction bending heats the area to be bent with an electric coil, and then the pipe or tube is bent with dies similar to those used in rotary draw bending. The metal is immediately cooled with water to temper it. It produces tighter bends than straight rotary draw bending.
    • Roll bending, also called cold bending, is used whenever large bends are necessary in the pipe or tubing, such as in awning supports, barbecue grill frames, or drum rolls, as well as in most construction work. Roll benders use 3 rolls on individual shafts to roll the pipe through as the top roller pushes down to bend the pipe. (Because the rolls are arranged in a triangle, this method is sometimes called pyramid bending.)
    • Hot bending, in contrast, is used considerably in repair work. The metal is heated at the place where it is to be bent to soften it.
    2. Advertisement
Method 2
Method 2 of 3:

Making a Right Angle Bend

  1. Image titled Bend Pipe Step 2
    1
    Bend a test pipe at a 90-degree angle. Not only will this familiarize you with how much force you need to apply to operate your bender, but this pipe will serve as a reference for future bends.[1]
    • To check the angle of your pipe, lay it against a carpenter's square with the outer bend facing the corner of the square. Both ends of the pipe should just touch the square's sides and run parallel to them.
  2. Image titled Bend Pipe Step 3
    2
    Find the place where the bend in the pipe starts. You should see or feel a small flat spot or distortion at the place where the bend starts and where it ends.
  3. Image titled Bend Pipe Step 4
    3
    Mark the ends of the bend with a permanent marker. Draw the line completely around the pipe.
  4. Image titled Bend Pipe Step 5
    4
    Lay the pipe against the square again to find the length of the pipe in the bend. Note the place on each side of the square where the pipe's markings touch. These should be the same distance from the inside corner of the square. Add these lengths together.[2]
    • If the markings on each end of the pipe bend touch the square at 6 inches (15 cm) from the inside corner of the square, the total length of the bent section of the pipe is 12 inches (30 cm).
  5. Image titled Bend Pipe Step 6
    5
    Find the place on your bending die where the bend begins. Place the bent tube back in your bender with the die used to bend it and note where on the die the mark on the pipe lines up. Mark this place with a dot of paint or by notching the metal with a file.
    • If you have more than one die (for different diameters of pipe), make a test bend for each die, as each diameter will require a different amount of metal to make a 90-degree bend.
    • Once you know how much pipe is needed to form the bend, you can calculate how long a piece of pipe you need by adding this figure (called the bend deduction) to the vertical and horizontal lengths of the pipe.
    6. Advertisement
Method 3
Method 3 of 3:

Making Multiple Bends

  1. Image titled Bend Pipe Step 7
    1
    Measure out the space your bent pipe will occupy. If you're making a roll bar for a dune buggy that will occupy a space 60 inches (150 cm) wide by 50 inches (125 cm) high, make a rectangle with these dimensions on a clean space of concrete floor with a piece of chalk.
  2. Image titled Bend Pipe Step 8
    2
    Divide the rectangle with a centerline. The centerline should bisect the longer (width) sides of the rectangle.
  3. Image titled Bend Pipe Step 9
    3
    Measure in from the top corners of the rectangle to where the horizontal portion of the bent pipe begins. If the top of the roll bar should run only 40 inches (100 cm), subtract this length from the width for the bottom, then measure half the distance in from each of the upper corners. This works out to a difference of 20 inches (50 cm), half of which is 10 inches (25 cm), which is the distance to measure in. Mark this distance in from each of the top corners.[3]
  4. Image titled Bend Pipe Step 10
    4
    Measure from the bottom corners to where the lower bend begins. If the distance from the bottom of the roll bar to the first bend is to be 40 inches (100 cm), measure and mark this distance up from each side of the bottom corners.
  5. Image titled Bend Pipe Step 11
    5
    Connect the markings where the bends will be made, using a straightedge or ruler. You can measure the connecting lines with a ruler.
    • In this example, the diagonal line connecting the marks on the horizontal and vertical lines is about 14 inches (70 cm) long.
  6. Image titled Bend Pipe Step 12
    6
    Lay your 90-degree bend pipe inside the top line of your frame. Lay it so that the horizontal straight end touches the inside of the upper horizontal line.[4]
  7. Image titled Bend Pipe Step 13
    7
    Slide the pipe until it touches the diagonal you drew.
  8. Image titled Bend Pipe Step 14
    8
    Mark the place where the bend mark intersects the frame line.
  9. Image titled Bend Pipe Step 15
    9
    Rotate the pipe so the other bend mark intersects the diagonal. Mark this place on the diagonal.[5]
  10. Image titled Bend Pipe Step 16
    10
    Repeat the last 4 steps for the other upper corner.
  11. Image titled Bend Pipe Step 17
    11
    Calculate the total length of pipe needed. Add together the measurements from the bottom corners to the first marks, the lengths of pipe between the lower bend, and the length between the upper bend.
    • In the above example, the vertical portions of the roll bar will each be 40 inches (100 cm) long, the diagonal portions will each be 14 inches (70 cm) long, and the horizontal portion will be 40 inches long. The total minimum length of pipe will be 40 + 14 + 40 + 14 + 40 inches (100 + 70 + 100 + 70 + 100 cm), or 144 inches (440 cm) long.
  12. Image titled Bend Pipe Step 18
    12
    Cut the pipe. Although the minimum length of pipe needed is 144 inches, it's a good idea to allow for error, add at least 4 inches (10 cm), making the total length 148 inches (450 cm).
  13. Image titled Bend Pipe Step 19
    13
    Find and mark the center of the pipe. You'll work from this point outward.
  14. Image titled Bend Pipe Step 20
    14
    Lay the pipe against the top line of your layout frame, aligning the pipe's center with the center line. Mark on the pipe where the upper bends are to start and finish using the marks on the frame.
    • You may also want to mark the direction of your bends by putting arrows on the pipe pointing outward.
  15. Image titled Bend Pipe Step 21
    15
    Make each of the upper bends with your bending tool. Be sure the pipe's seam is to the inside when you bend; this prevents twisting or kinking during the bending process.[6]
    • To ensure your bender is set to the correct angle, you can prepare a reference tool of 2 flat pieces of metal whose ends are attached to a pivot. Bend this tool to the angle indicated on your frame, and then match the bending angle of your bending tool to this angle.
    • After making each bend, lay the pipe against your frame to check that the angle of the bend is correct.
  16. Image titled Bend Pipe Step 22
    16
    Make each of the lower bends with your bending tool. Follow the same procedures as outlined in the previous step.
  17. Image titled Bend Pipe Step 23
    17
    Cut off any excess from the ends of the bent pipe.
    18. Advertisement

Community Q&A

  • Question
    How much does the pipe grow with a 90 degree bend?
    Community Answer
    Community Answer
    The pipe will not grow in length if you bend it properly so that it does not collapse across its diameter.
  • Question
    How much time does it take to bend tubing?
    Community Answer
    Community Answer
    If you have 1/4-inch copper tubing you can bend it with your finger in seconds. If you have a thicker tube and the correct bending tools, seconds or minutes. It depends on the tubing, the materials you have, and the number of bends you wish to make.
  • Question
    What are the procedures for cleaning pipelines?
    Community Answer
    Community Answer
    Cut the pipe into tiny pieces, like bracelets, then when done cleaning the separate pieces, glue and tape back together.
Advertisement

Warnings

  • Regularly inspect your bending tool and dies for wear after bending pipe. Even pins and bolts of 1/2 to 5/8 inch (1.25 to 1.56 cm) in diameter will bend and fail after a while.
    ⧼thumbs_response⧽
  • Bending pipe 2 inches (5 cm) or more in diameter is best left to a professional.
    ⧼thumbs_response⧽
Advertisement

Things You'll Need

  • Length of pipe
  • Bending tool and dies
  • Flat, clean floor or large table
  • Chalk (or sheet of butcher paper and pencil if using a table)
  • Carpenter's square
  • Pipe cutter
  • Assistant (for long, heavy pipe)


You Might Also Like

Bend Aluminum Pipe
How to
Bend Aluminum Pipe
Bend EMT Conduit
How to
Bend EMT Conduit
Bend a 3‐Point Saddle
How to
Bend a 3‐Point Saddle
Measure Pipe Size
How to
Measure Pipe Size
Fix a Leaky Sink Drain Pipe
How to
Fix a Leaky Sink Drain Pipe
Fix Leaking Pipes
How to
Fix Leaking Pipes
Thread Pipe
How to
Thread Pipe
Repair PVCHow to Easily Patch and Repair PVC Pipe
Hide Pipes
How to
Hide Pipes
Fix a Broken Pipe
How to
Fix a Broken Pipe
Clear a Clogged Waste Pipe
How to
Clear a Clogged Waste Pipe
Clean a P‐Trap or U‐Bend
How to
Clean a P‐Trap or U‐Bend
Join PPR Pipe
How to
Join PPR Pipe
Bend Copper Tubing
How to
Bend Copper Tubing
Advertisement

References

  1. ↑ https://www.homedepot.com/c/ah/how-to-bend-tube-and-pipe/9ba683603be9fa5395fab9019bf513f7
  2. ↑ https://www.homedepot.com/c/ah/how-to-bend-tube-and-pipe/9ba683603be9fa5395fab9019bf513f7
  3. ↑ https://support.jd2.com/MiscDown/dl/TemplateBendingTutorial.pdf
  4. ↑ https://support.jd2.com/MiscDown/dl/TemplateBendingTutorial.pdf
  5. ↑ https://support.jd2.com/MiscDown/dl/TemplateBendingTutorial.pdf
  6. ↑ https://www.thefabricator.com/thefabricator/article/tubepipefabrication/tube-and-pipe-basics-how-to-achieve-the-perfect-bend

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 14 people, some anonymous, worked to edit and improve it over time. This article has been viewed 245,320 times.
117 votes - 72%
Co-authors: 14
Updated: February 16, 2022
Views: 245,320
Categories: Piping
Advertisement