The process of gluing acrylic is slightly different than the process of gluing other substances, such as paper or wood, together. Rather than working as a simple adhesive, acrylic cement creates a chemical reaction that physically bonds or welds plastic. Though it sounds complicated, the process can be quite simple - as long as you're safe, meticulous, and patient. All you have to do is prepare and wait.

Part 1
Part 1 of 3:

Choosing an Optimal Work Environment

  1. 1
    Find an appropriate workspace. Since you'll be working with an adhesive that can cause fumes, you want to first make sure you are in a well-ventilated area. For example, working outdoors or in a room with more than one window.[1]
    • Position your work area between windows or between a window and open doorway.
    • You should also set up a box fan or two to blow air away from you.
    • A room that has an exhaust fan works well, too.
  2. 2
    Take the appropriate safety precautions. This means wearing safety goggles, gloves, and a facemask. Outside of the potential vapors from the acrylic cement, you also want to make sure that any refuse from cutting or sanding the acrylic doesn't get in your lungs or eyes.
    • Make sure you are also following the directions on the acrylic cement closely to avoid any mishaps.
    Advertisement
  3. 3
    Select your work surface. Whether you are planning to glue in a workroom, a garage, or even your kitchen, you want to make sure that the surface area you’re using is compatible with acrylic cement. Try to stick to an area that’s concrete, metal or wood. Do not glue acrylic on a surface containing glass or paper.
  4. Advertisement
Part 2
Part 2 of 3:

Setting Up Your Materials

  1. 1
    Examine the edges of the acrylic. Make sure that the borders of the acrylic you want to join are flat and free of bumps or cuts. Acrylic cement will not adhere or sink into grooves and crevices like regular glue does on wood or paper. Instead, it softens the acrylic and chemically bonds the pieces together, so it's important they are as flat as possible.[2]
    • If you notice any rough areas, use a router (a power tool with a shaped cutter) or light sandpaper to ensure that the edges are perfectly smooth and square. However, do not sand the edges so that they become round.
    • Make sure that any surfaces being bonded together are lightly sanded and not shiny, as a very smooth surface is tough to bond together.
  2. 2
    Clean the acrylic with isopropyl alcohol. Once you have sanded and smoothed the sides of your acrylic, wipe over it with a clean cloth and alcohol. Using Isopropyl alcohol will help guarantee that all dirt, dust, and other fragments have been removed. It will also remove any residual oils left by your hands, which can interfere with gluing.
    • Be sure that your surfaces are totally dust-free – this is really important to the process.
  3. 3
    Prepare your acrylic cement/glue. The most common glue for acrylics is a solvent-based glue like Weld-On 4, which can be found on Amazon for under $15. This glue should also come with its own applicator bottle and needle. To use, simply fill the applicator bottle, via a funnel, until the bottle is about 75% full.
    • Once filled, squeeze the bottle gently to allow some of the air inside to escape.
  4. Advertisement
Part 3
Part 3 of 3:

Applying the Glue

  1. 1
    Join the acrylic pieces. Place the pieces of acrylic together as you want them to be joined. They should meet at a 90-degree angle. You can then use a combination square to guarantee that the pieces are angled correctly. Once set up, use your hands or a clamp to hold the sections together.
    • Always do a dry run first, making sure the pieces fit before applying any glue.
    • It helps to assemble the object together with adhesive tape. Then the adhesive can be placed accurately without juggling the parts.
  2. 2
    Position the applicator bottle and apply glue. Turn the bottle upside down and place the needle above the edge where the two pieces of acrylic meet. Squeeze the bottle with mild pressure as you move along the joined edges. You want to pull the bottle towards you. The acrylic cement should run in between the joined edges and fill in any seams or spaces as you move it along.[3]
    • Try to lightly squeeze the bottle and move it without stopping, this will ensure you don't over-glue the acrylic.
    • If you are gluing for a box corner joint, apply the acrylic cement to the inside edge of the sheeting. However, if you are gluing for flat joints, apply the cement to both sides of the sheeting.[4]
    • Do not allow the acrylic cement to touch any piece of the acrylic you do not want to be glued. Acrylic cement will permanently damage any surface it touches. If you do drip acrylic cement onto the acrylic, allow the cement to evaporate. Do not wipe it off.
  3. 3
    Allow the acrylic cement to set. Most acrylic cement will take around 10-15 minutes to set initially. During this time you can use your hands or a clamp to hold the edges together. Once they are secure, they should take 24-48 hours to cure to full-strength.[5]
    • If the pieces have been adhered well, the dried acrylic cement will be clear. Before this time, the acrylic should appear as a cloudy white.
  4. 4
    Trim the acrylic. If there are any excess or overlapping pieces of acrylic, you can cut these off with a router (a power tool with a shaped cutter). However, be careful of heat generation, which could melt the acrylic. You should also make sure the acrylic is properly set before you try to manipulate it in any way.
  5. Advertisement

Expert Q&A
Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow

  • Question
    Can I buy the glue at Walmart or Home Depot?
    Mark Spelman
    Mark Spelman
    Construction Professional
    Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
    Mark Spelman
    Construction Professional
    Expert Answer

    Support wikiHow by unlocking this expert answer.

    You can buy acrylic glue at most general stores, including Walmart or Home Depot.
  • Question
    How can I glue an acrylic sheet to MDF board for kitchen cupboards?
    Mark Spelman
    Mark Spelman
    Construction Professional
    Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
    Mark Spelman
    Construction Professional
    Expert Answer

    Support wikiHow by unlocking this expert answer.

    Try using a 3M spray adhesive to glue an acrylic sheet to an MDF board.
Advertisement

Things You'll Need

  • Acrylic
  • Acrylic cement
  • Applicator bottle
  • Funnel
  • Router
  • Sandpaper
  • Alcohol
  • Clean cloth
  • Concrete, metal or wood work surface
  • Combination square
  • Safety goggles
  • Rubber gloves
  • Mask

About This Article

Mark Spelman
Co-authored by:
Construction Professional
This article was co-authored by Mark Spelman. Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987. This article has been viewed 327,264 times.
49 votes - 87%
Co-authors: 13
Updated: February 12, 2023
Views: 327,264
Categories: Glue
Article SummaryX

Before gluing your acrylic, take safety precautions by wearing goggles, gloves, and a face mask. Then, lightly sand the edges of the acrylic before cleaning them with alcohol. Place the pieces of acrylic in the correct position, then use a combination square to guarantee the angle. Finally, apply the glue by squeezing the bottle gently along the joint. To ensure everything stays in place while the glue dries, fix the acrylic with a clamp. For tips on finding a good workspace for gluing acrylic and how to trim it, read on!

Did this summary help you?
Advertisement