This article was medically reviewed by Jennifer Boidy, RN. Jennifer Boidy is a Registered Nurse in Maryland. She received her Associate of Science in Nursing from Carroll Community College in 2012.
This article has been viewed 52,446 times.
Bulb syringes are typically used to help clean out the nasal passage of infants and young toddlers. They can also be used to clear out ear wax.[1] Because syringes are placed into the nose or ears, it is important that they are thoroughly cleaned and sterilized. This will help to prevent the development of mold and bacteria. In order to clean a bulb syringe, you should wash the syringe in warm soapy water and then rinse the syringe. If you are planning to store the syringe for a period of time, you should sterilize the syringe with hot water and rubbing alcohol.
Steps
Washing the Syringe with Soapy Water
-
1Fill a small bowl with cool soapy water. Each time you use a bulb syringe, you should clean it with cool soapy water. This will remove anything that may remain in the syringe after use. To do this, fill a small bowl with cool soapy water.[2]
- Don't use warm or hot water because that will make it harder to remove the mucus from the bulb.[3]
-
2Soak the syringe in water. Place the syringe so that it is fully submerged in the water. Leave the syringe in the water for a few minutes.Advertisement
-
3Squeeze the syringe with the tip in the soap mixture. Place the tip of the syringe in the water and squeeze the bulb so that the syringe fills with the soapy water.[4]
-
4Release the soap. Aim the hole of the syringe in the direction of the water and squeeze the bulb to release the water down the drain.
-
5Repeat three times. Continue to fill up the syringe with cool soapy water and then release the water. Do this three to four times in order to make sure that the inside of the syringe is completely cleaned.
Rinsing and Drying the Syringe
-
1Rinse the syringe with running water. Place the syringe under a tap of warm running water. This will help remove any soap suds from the outside of the syringe.
-
2Fill a small bowl with warm water. Empty the bowl filled with soapy water and then thoroughly rinse under running water. Then, fill the same bowl with warm water. Do not add soap to the water.[5]
-
3Squeeze the syringe with the tip in the water. Place the tip of the syringe into the warm water and squeeze the bulb. This will fill the syringe with warm water.
-
4Shake the water to rinse the inside. Place your index finger over the hole in the syringe to prevent water from leaking out. Then, shake the syringe so that the water rinses the inside of the syringe.
-
5Release the water. Aim the hole of the syringe at the bowl of water and the squeeze the bulb to release the water. You could also release the water directly into your sink.
-
6Repeat until completely rinsed. Continue to fill the syringe with water, shake, and release the water. This will thoroughly rinse the syringe and remove any remaining soap from inside the bulb.
-
7Suspend the syringe upside down in a glass. Place the syringe upside down in a glass, with the tip facing the bottom of the glass. This will allow the water to drip out of the syringe and dry.[6]
Sterilizing the Syringe
-
1Place the syringe in boiling water for 10 minutes. Before storing a bulb syringe for a sustained amount of time, you should sterilize it to prevent the development of mold and bacteria. Heat a pot of water on the stove until it is boiling. Place the syringe in the water for ten minutes.[7]
-
2Remove the syringe from the water. After 10 minutes, carefully remove the bulb syringe from the water. Use a pair of heat-proof tongs or a metal spoon to remove it. Then, while wearing an oven mitt, pick up the syringe and slowly squeeze the excess water into the sink.
-
3Rinse with rubbing alcohol. Fill the bulb syringe with rubbing alcohol. Place your finger over the hole to prevent the liquid from leaking out. Then, gently shake the syringe so that the rubbing alcohol fully cleanses the inside of the syringe. Squeeze the bulb to release the rubbing alcohol.[8]
-
4Dry upside down. Place the syringe upside down in a cup. This will allow any excess rubbing alcohol to drip out of the syringe.[9]
- Once the syringe is completely dry, store in a dry and cool space.
Things You’ll Need
- Bulb syringe.
- Dish soap.
- Cup.
- Pot.
- Thermometer.
- Rubbing alcohol.
Warnings
- Never wash a bulb syringe in the dishwasher.⧼thumbs_response⧽
- Bulb syringes can develop mold if they are not cleaned between each use and sterilized before being stored.⧼thumbs_response⧽
References
- ↑ https://www.chkd.org/patients-and-families/health-library/way-to-grow/suctioning-your-childs-nose-and-mouth/
- ↑ http://www.womans.org/our-services/mother-and-baby/newborn-care/baby-care/bulb-syringe/
- ↑ https://www.youtube.com/watch?v=s7_4uAcZtqU
- ↑ https://www.youtube.com/watch?v=s7_4uAcZtqU
- ↑ https://www.babycenter.com/0_how-to-use-a-bulb-syringe-or-nasal-aspirator-to-clear-a-stuf_482.bc
- ↑ https://www.babycenter.com/0_how-to-use-a-bulb-syringe-or-nasal-aspirator-to-clear-a-stuf_482.bc
- ↑ https://www.conehealthybaby.com/chb/your-new-baby/home-care/using-the-bulb-syringe/
- ↑ https://www.drugs.com/cg/how-to-use-a-bulb-syringe.html
- ↑ https://www.drugs.com/cg/how-to-use-a-bulb-syringe.html
Medical Disclaimer
The content of this article is not intended to be a substitute for professional medical advice, examination, diagnosis, or treatment. You should always contact your doctor or other qualified healthcare professional before starting, changing, or stopping any kind of health treatment.
Read More...