How to Clean Tripe

Co-authored by wikiHow Staff

Last Updated: September 6, 2019 References

Tripe comes from the lining of the stomach of various farm animals, most commonly from the cow. It is a highly valuable asset in cooking with a wide range of uses. Due to the fact that it's an internal organ and the condition it's sold in, tripe needs to be rigorously cleaned before being used in cooking. By rinsing, boiling, and cutting the tripe, you will be able to use it to its maximum potential in your next meal.

Part 1

Part 1 of 3:

Removing the Excess

1
Rinse the tripe. Run the tripe through cold water to remove any loose waste products attached to it.
2
Remove the fat. To find excess fat, you'll need to inspect the non-textured side of the tripe.
- If you see any fat, pull it up and slice it off with the knife. Fat will look noticeably different to the tripe, being more pale and feeling more like rubber. Tripe is a low fat meat so you shouldn't have too much fat to remove.
- Other unnecessary parts such as remnants of food from the animal's stomach will be removed by other processes during the cleaning.
- Do not cut the tripe into strips or sections yet.
Advertisement
3
Rub the tripe with rock salt and rinse it with vinegar. This process will loosen any unwanted waste products and make the surface smooth without damaging the tripe itself. ^{[1]
X
Research source}
- Vinegar is acidic and is therefore useful at getting deep into the layers of the tripe and effectively cleaning it.
- Next, use the rock salt again and rub it across the tripe the same way you just did. The goal here is to clean the tripe as effectively as possible.
- Keep repeating the process until the tripe looks and feels like it's both smooth and clean.
4
Scrape the surface. Using the spine of a sharp knife, scrape the surface of the tripe to remove any imperfections. Honeycomb tripe can be hard to sufficiently clean with a knife due to its relative lack of flatness. For this you can use a toothbrush instead. ^{[2]
X
Research source}
5
Rinse the tripe again. Gently rinse the tripe under cold water again for a few minutes to remove any remaining grit from the meat.
- While bleached tripe will already be free from grit, it's a good idea for you to rinse it to get rid of the smell.
- The chlorine on bleached tripe can also get into the other foods you are cooking, which could make the whole meal smell like bleach. ^{[3]
  X
  Research source}

Part 2

Part 2 of 3:

Boiling the Tripe

1
Steep the tripe in a bowl of water for 1 hour. Make sure that the tripe is completely covered by the water. This ensures that all of the tripe is being sufficiently soaked.
2
Place the tripe in a large pot. Pour some cold water into the pot and bring it to the boil. ^{[4]
X
Research source}
- Allow the tripe to boil for between 30 and 45 minutes.
- Add a tablespoon of salt for every liter of water in the pot.
- Boiling the tripe is important as it removes any dangerous bacteria from the tripe.
- It also makes the tripe easier to cut and slice later, as well as reducing the cooking time when preparing the meal.
3
Drain the pot and rinse the tripe again. Use cold water to wash the tripe. Rigorously and repeatedly rinsing the tripe is very important to ensuring the tripe is as clean as it can be.
4
Refill the pot and allow it to simmer. Then place the tripe back in the pot. Allow the tripe to simmer in the pot for 2 to 3 hours. The water will slowly evaporate so remember to occasionally add water into the pot to keep the tripe covered.

Part 3

Part 3 of 3:

Cutting the Tripe

1
Place the tripe on the cutting board. Lay the smoother side down and as flat as possible. The tripe is now at its easiest to cut after the boiling and simmering.
2
Inspect the tripe for unnecessary parts. Now that the tripe has been thoroughly cleaned, have a look at it once more to see if there is any fat or grit that needs to be sliced off. Chop off anything you see that shouldn't be there.
3
Cut the tripe in half. Using a sharp knife, slice the tripe in half from top to bottom, splitting it into two separate pieces. ^{[5]
X
Research source}
- It is easiest to cut the tripe at this stage of the process as the boiling has hardened it.
- If you try to cut the tripe before this stage, it will be far too tender and it will be very difficult to accurately and cleanly cut it.
4
Cube the tripe. Take one of the tripe pieces you have and slice it into long, thin strips. Then take a single strip and cut it into 2 inch by 2 inch cubes. Repeat the process for the rest of the tripe. ^{[6]
X
Research source}
- Now your tripe is ready to be used in whichever way you desire. Tripe can be used in a variety of ways, from grilling to making tripe soup. It can also be used in a whole host of different dishes, including Asian and Mexican meals among others.

Community Q&A

Question

I purchased cut-up tripe from my butcher, and it is still very black. How do I whiten it?

Community Answer

Put it in the vinegar water. That will whiten it and give it more taste.
Question

The tripe made my pot black. How do I clean the pot?

Community Answer

Try using baking soda and water and letting that sit on the pot for an hour or two before washing off and cleaning it as usual.
Question

Can I clean tripe with bicarbonate of soda?

Ben Tri

Community Answer

Doing that is not recommended at all. Water will be sufficient. Bicarbonate will alter the taste and quality of the trips.

Warnings

Remember to wash your hands thoroughly and frequently while handling the raw tripe. Tripe is raw meat and improper hand washing could lead to salmonella or another illness.

⧼thumbs_response⧽
Helpful 1 Not Helpful 0