This article was co-authored by Victor Belavus. Victor Belavus is an Air Conditioning Specialist and the Owner of 212 HVAC, an air condition repair and installation company based in Brooklyn, New York. In addition to HVAC and air conditioning units, Victor also specializes in furnace repair and air duct cleaning. He has over 10 years of experience working with HVAC systems.
wikiHow marks an article as reader-approved once it receives enough positive feedback. In this case, several readers have written to tell us that this article was helpful to them, earning it our reader-approved status.
This article has been viewed 766,945 times.
Air conditioning uses up 20 percent of the electricity used in the U.S. To reduce your use of air conditioning and help the environment, you can build an conditioner with either a box fan and a cooler or with a box fan and a radiator. Follow these instructions to build your own air conditioner.
Steps
Build an Air Conditioner with a Box Fan and a Cooler
-
1Remove the front gridded panel of the fan.
-
2Wrap 1/4" (6mm) diameter copper tubing around in concentric circles, starting at the center of the exterior side of the panel. This tubing has an inner diameter of 1/4" (6mm) and an outer diameter of about 3/8" (9.5 mm).
- First, attach one end of the tubing to the center of the panel using zip ties.
- Wrap the tubing around in larger and larger concentric circles, leaving spaces between the circles of about 3/8" (9.5 mm). Connect the tubing to the panel with zip ties.
Advertisement -
3Re-attach the panel to the fan.
-
4Connect one end of a piece of 3/8" (9.5 mm) clear plastic tubing to a fountain pump. This tubing has an inner diameter of 3/8" (9.5 mm) and an outer diameter of about 1/2" (12 mm).
-
5Connect the other end to either end of the copper tubing. Slip the plastic tubing over the copper tubing and clamp it on with a hose clamp.
-
6Connect another piece of plastic tubing to the other end of the copper tubing using a hose clamp.
-
7Fill a cooler with ice water. Stick the end of the piece of tubing that is not connected to the fountain pump into the bottom of the cooler.
-
8Put the fountain pump in the cooler, submerged in the ice water.
-
9Lay a towel under the fan to catch the condensation that drips from the copper tubing.
-
10Plug in the fountain pump and turn on the fan.
Build an Air Conditioner Using a Recycled Radiator
-
1Clean your radiator before you use it. You can soak it in water and mild soap and then let it air dry.
-
2Place a high-speed fan behind the radiator. You may have to place some objects under the radiator to line it up with the fan.
-
3Attach a garden hose to a spigot on the exterior of your house.
-
4Connect the vinyl tubing to the inlet tube on your radiator. You may have to try a couple of sizes to find the right size of tubing that will fit over the copper tubing from your radiator. The tube length should be long enough to connect with the garden hose outside.
-
5Feed the tubing through a window and attach the tubing to the spout end of your garden hose with duct tape. You may need to cut a small hole in your window screen to make this work.
-
6Coil your garden hose up and wrap it in a towel for insulation. Wrap pipe insulation around the exposed end to keep the water cold.
-
7Attach another length of plastic tubing to the outlet tube of your radiator.
- Thread the tubing upward through your window so that the water is expelled onto your roof or into your gutters.
- If you expel water onto your roof, then you'll need to make sure that the overflow hitting the ground doesn't flood your basement. Try placing a large plastic garbage can beneath the stream to catch the water, and recycle the water in your garden.
-
8Attach a small hand valve to the plastic inlet tubing that goes into the radiator.
- Cut the plastic inlet tubing to leave a 6" (15 cm) stub attached to the copper inlet tube of the radiator.
- Attach the end that releases water to the stub of inlet tube.
- Connect the side that pulls in water to the tube that's connected to your garden hose.
-
9Open the hand valve completely. On the outside of your house, open the garden hose spigot to find the right water flow volume.
-
10Plug in the fan and turn it on. When you're ready to switch off your homemade air conditioner, close the hand valve and unplug your fan.
Community Q&A
-
QuestionIs there any harm to be aware of when making the homemade air conditioner?DvortygirlCommunity AnswerThe devices described in this article aren't true air conditioners. They're really just heat exchangers. Other than keeping your fingers out of the fans and generally working safely, the main thing to be aware of is managing moisture. Make sure any water circulating, along with any condensation, is captured and doesn't get into carpet, flooring, etc.
Warnings
- If you don't own your own home, then make sure you discuss expelling water onto your roof or into your gutters with your landlord. Be prepared to repair or replace your window screen when you move out.⧼thumbs_response⧽
- Water and electricity don't mix.⧼thumbs_response⧽
Things You'll Need
- Box fan
- 20 feet (6 m) 1/4" (6 mm) copper tubing
- Zip ties
- 3/8" (9.5 mm) plastic or nylon tubing
- Cooler
- Two small hose clamps
- Towel
- Radiator
- Garden hose
- Exterior spigot
- Pipe insulation
- Small hand valve
- Fountain Pump
References
- Videos provided by fixitsamo
- How to Make Your Own Homemade Air Conditioner
- The Black Beauty
About This Article
To build your own air conditioner using a box fan and a cooler, start by unscrewing the grid on your fan. Once that is off, twist 1/4" diameter copper tubing in concentric circles at the center of the grid you've just taken off, attaching the tubing to the fan grid with zip ties. Then, connect the loose end of cooper tubing to clear pliable tube. Once that is done, fill a cooler with ice water and place a fountain pump inside the water. Submerge your plastic hoses in the ice water, plug in your pump, and your homemade A/C should be ready to go. To learn how to build your own air conditioner using an old radiator and a hose, read on!