X
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 11 people, some anonymous, worked to edit and improve it over time.
This article has been viewed 118,560 times.
Learn more...
One of the most versatile electric tools available to a woodworker is the router. The router comes in 2 forms, the fixed base and the plunge base. The router used most by the woodworker is the plunge base. It may seem more difficult to use at first, but you can learn how to use a plunge router by following the steps below.
Steps
-
1Examine the plunge router. You will note that it contains an electric motor mounted between two posts. The motor rests on top of springs and is attached to a flat base that guides the motor down at a 90 degree angle.[1]
- The motor rises back into position when downward pressure is released, raising the router bit above the base.
- Attached to a collet, the motor connects much like a hand drill chuck. It comes in 2 sizes, 1/4 inch and 1/2 inch (as well as 8 mm and 12 mm in metric sizes). This is where the router bit does the cutting.
-
2Notice the plunge router motors come in a variety of sizes ranging from 1.5 horsepower to 3.5 horsepower. The bigger the motor, and consequently the collet, the bigger the router bit. As a result, the cut is deeper.[2]Advertisement
-
3Research and buy what you can afford. Remember, a higher price does not necessarily mean a better tool.[3]
-
4Use jigs and guides with the plunge router. These are often shop made or bought as add-on accessories.
- The most common jig will be used for cutting dadoes. Dadoes are used in joining two pieces of wood at 90 degrees, such as adding a kitchen cabinet shelf to a side piece. This type of joint uses a straight cut router bit for dadoes.
- Clamp the guide into place so that, when the router bit is plunged downward, the bit will line up with the dado joint you want to cut.
-
5Install the router bit in the collet, adjusting the gauge for the depth of cut you need.[4]
-
6Put the router up against the guide. Pull the trigger and push downward while holding the router with both hands. This act will engage the bit with the wood.
-
7Move the router from left to right in the direction of the cut.
-
8Release the downward pressure on the handles when you finish the cut. The router will retract into the base.
-
9Use other bits to cut profile edges with a plunge router following the same procedure.
- Install the desired router bit in the collet. Most profile-edge bits, like a round over or Roman Ogee bit, will have a sleeve bearing that will guide the bit along the edge of the work piece.
- Set the depth gauge for the amount of bit you want to use.
-
10Set the plunge router base onto the surface. Firmly press downward, holding the handles while pulling the trigger.[5]
- Push in against the edge engaging the bit while fully extended to the depth needed.
-
11Make the cut with the router moving from left to right.
-
12Release the downward pressure on handles and the bit will retract.
Advertisement
Community Q&A
-
QuestionHow do I build a router table?DonaganTop AnswererTake a look here: TheBalance.com/free-router-table-plans-1357138.
-
QuestionHow do I use an angle grinder as a wood saw?DonaganTop AnswererThere's an old saying: use the right tool for the job. There are so many kinds of saws available, it's hard to imagine that you couldn't find a size and tooth pattern to fit the job at hand. A grinder will burn your wood and generally exasperate you unless there's very little wood to remove. In that case you might consider a file, a sander, or a chisel.
Advertisement
Warnings
- Wear safety glasses and a dust mask when working with the plunge router.⧼thumbs_response⧽
- Do not wear loose clothing while operating a router.⧼thumbs_response⧽
Advertisement
Things You'll Need
- Plunge router
- Router bits
- Guides or jigs with clamps
- Dust mask
- Safety glasses
References
- ↑ https://www.youtube.com/watch?v=8Vl8Jbw3cSk
- ↑ https://www.youtube.com/watch?v=8Vl8Jbw3cSk
- ↑ https://www.wwgoa.com/article/router-basics-how-to-use-a-router/
- ↑ https://www.wwgoa.com/article/router-basics-how-to-use-a-router/
- ↑ https://www.youtube.com/watch?v=eOKco1aOygY
- http://www.popularmechanics.com/home/reviews/4301758?click=main_sr
- https://www.youtube.com/watch?v=rJGXqtOsB6A
- https://www.woodmagazine.com/woodworking-tips/techniques/routing/plunge-router?mode=step_by_step
About This Article
Advertisement