How to Paint Skirting Boards

Last Updated: July 8, 2021 References

Skirting boards, the wood trim that separates the floor from the wall, are a seemingly minor aspect of a room. Yet because they fall victim to bumps from furniture, feet, and toddler Tonka trucks, they can easily get scuffed and dirtied — giving a room a tired look. However, skirting boards with a fresh coat of paint can bring a satisfying, finished feeling to a space. With the correct materials and preparation, painting or refreshing your skirting boards is easy.

Part 1

Part 1 of 2:

Preparing to Paint

1
Clear all furniture out of the way. Move all of the furniture in the room to another room, or at least out of the way from the immediate area where you will be painting. It’s not necessary to cover furniture, but just make sure it is at least ²⁄₃ to 1 m (2.2 to 3.3 ft) away.
2
Sand the skirting boards with fine 180-grit sandpaper. This step is especially important if you are working with skirting boards that were previously painted with glossy paint.^{[1]
X
Expert Source

Archie Guerrero
Commercial & Residential Painting Specialist
Expert Interview. 17 June 2021.} Rub fine sandpaper (180-grit) wrapped around a wood block in small circles on the skirting boards to create a rougher surface on the skirting boards that the paint will stick to.^{[2]
X
Research source}
- You don’t have to entirely remove the paint that was there before, but sand enough so that the shine on the board disappears.
- Turn to 80- to 120-grit sandpaper if you want to get rid of bumps or imperfections (i.e. large globs of old paint).^{[3]
  X
  Research source}
- Sandpaper sponges also work great, especially for sanding surfaces (like skirting boards) that aren’t completely flat.^{[4]
  X
  Research source}
Advertisement
3
Vacuum up the dust from the skirting boards and your workspace. Sanding generates a lot of dust, so do your best to clear it all out before starting to paint. Vacuum the floor or carpet around where you were sanding. Be particularly mindful of the little crack between the skirting boards and the floor, as this is a notorious dust hiding place.
- Use a thinner hose or brush attachment for your vacuum if you have one.
4
Clean the skirting boards with a damp sponge. Fill a bucket with water and non-soapy detergent (i.e. Dirtex, Spic & Span, or TSP No-Rinse Substitute). Dip your sponge in this mixture and wring the sponge out in the bucket before applying it to the boards.^{[5]
X
Expert Source

Archie Guerrero
Commercial & Residential Painting Specialist
Expert Interview. 17 June 2021.} Then, wash the wood with the sponge by starting at the bottom of the skirting board and using up-and-down strokes.^{[6]
X
Research source}
- Give it at least an hour to dry before moving forward. If you’re short on time, you can use a dry brush to get rid of the dust instead.
5
Cover the area where the wall meets the skirting board with masking tape. Gently press 5 cm (2.0 in) masking tape (also called blue or painter’s tape) on the wall just above the skirting board. That way, if your brush accidentally veers off the skirting board, your wall will be protected.^{[7]
X
Expert Source

Archie Guerrero
Commercial & Residential Painting Specialist
Expert Interview. 17 June 2021.}
6
Protect the floor with masking tape. Accidentally getting paint on the floor is probably the last thing you want. If your room has hardwood floors, place strips of masking tape on the floor where the skirting board meets the floor. Do this for the whole room.
- With carpet, the process is a little more involved. If you’re working with a shorter kind of carpet, insert a putty knife in the space between the carpet and the skirting board at an angle to push the carpet away from the wall. ^{[8]
  X
  Research source} Then, place the masking tape along where the skirting board meets the floor, leaving a slight lip (about ¹⁄₂ cm (0.20 in)) that is pressed onto the skirting board itself. Then, take your putty knife and press it down in the space between the skirting board and the carpet, pushing the tape down and leaving the skirting board fully exposed.
- However, with longer shag carpet (sometimes known as saxony or frieze), you’re out of luck.^{[9]
  X
  Research source} The best way to protect the carpet is to pull it up and away from the skirting boards before painting.
7
Treat any exposed wood with a knotting solution. If your skirting boards haven’t been painted before, use a small brush to gently brush 1-2 coats of a knotting solution over any knots (dark spots) in the wood. Let it dry for 24 hours.^{[10]
X
Research source}
- This prevents any yellow knot marks in the wood from showing through and discoloring your paint.^{[11]
  X
  Research source}
8
Prime the skirting board with an oil-based primer. Using your angled 5 cm (2.0 in) brush, brush a layer of primer over the skirting boards. Use an oil-based primer for maximum durability, and let it dry for 24 hours. ^{[12]
X
Research source} This will help the paint stick to the skirting boards.
- Some primers have shorter dry times — read the label on the can of your primer for more information.

Part 2

Part 2 of 2:

Painting

1
Choose an oil-based, semi-gloss paint. Oil-based paint is recommended for skirting boards because, even though it has a longer dry time, its thick consistency ensures that it will fill cracks and divots in skirting board detailing and hold up against wear for a long time. ^{[13]
X
Research source} Avoid using flat emulsion to paint, as this will result in skirting boards that can easily be marked up.
- In terms of gloss, go with semi-gloss paint (also sometimes called satin). Skirting boards are meant to be decorative, and semi-gloss paint will result in smoother, more reflective, and more attractive skirting boards.^{[14]
  X
  Research source}
2
Dip your brush about a third of the way into the paint. Use your angled 5 cm (2.0 in) brush. You don’t want it to be overloaded with paint, so brush it against the inside rim of the paint can to remove any excess.^{[15]
X
Research source}
3
Start painting from a corner of the room. If you are right-handed, paint right to left. If you are left-handed, paint left to right. This will eliminate the need to awkwardly position your body, and it’ll also minimize your chances of dropping paint on the floor.
4
Cut in the edges of the skirting board. Start painting on the rounded top edge of the skirting board using a stroke called cutting. Hold your brush so that the wide face of the bristles are facing the floor, and drag the narrow part along the top of the skirting board.^{[16]
X
Research source} Then, repeat this process for the bottom of the board.
5
Apply strokes in the same direction on the middle of the skirting board. Hold your brush at about at 45-degree angle and apply the paint in one stroke in one direction on the widest part of the skirting board. Just take it slow. If any paint drips where it’s not supposed to on the board, blend it in before it dries and forms a bump. ^{[17]
X
Research source}
- Avoid starting a brush stroke on paint that’s already been smoothed. This will leave a pretty obvious brush mark. Try to start strokes in an unpainted area and brush toward finished areas. Use lighter strokes as you get closer to smoothed sections.^{[18]
  X
  Research source}
6
Feather the areas between strokes. Each stroke will require dipping your brush back in the paint. For the areas in between strokes, however, raise the brush slightly and lightly feather the paint together to avoid lap marks (marks that show where one stroke ended and another began). Feathering means gently using the tip of the brush to create a smooth transition between separate strokes. You will not need a lot of paint on your brush to do this. ^{[19]
X
Research source}
- A common mistake is trying to blend the paint too long after it’s been applied. This results in unsightly brushstrokes. Paint starts to dry as soon as you put it on, so work the paint while it’s wet and then move on to another section.^{[20]
  X
  Research source}
7
Let the paint dry for 24 hours. You’ll need to paint at least 2 coats, especially if you’re painting a lighter color over a darker one. Give the first one at least 24 hours to dry, or follow the drying time as according to the instructions on the paint can.
8
Sand down any imperfections in the paint using extra fine sandpaper. Before putting down your second coat, sand down any bubbles or areas in the paint that aren’t smooth. Otherwise, they will just get worse when you put the second coat on. Use extra fine sandpaper (240, 320, or 400-grit).^{[21]
X
Research source}
- Remember to remove any dust with a dry brush before beginning to paint again. ^{[22]
  X
  Research source}
9
Paint on your second coat. You may need to paint on more than 2 coats, especially if you are painting a lighter color over a much darker one. White is the most popular color for skirting boards, so you may find yourself in this situation. Don’t forget to sand between coats.
10
Brush on polyurethane varnish. This step is optional, but polyurethane varnish helps skirting boards hold up longer against scratches and scuff marks. This is recommended if you are painting the skirting boards in a house that will have small children or pets.^{[23]
X
Research source}
- Repeat the same process that you used for priming when applying varnish. Check the packaging of your varnish for specific dry times, and wait until it’s completely dried before moving furniture back up against the skirting boards.

Expert Q&A

Question

How much do you have to sand gloss paint before repainting?

Archie Guerrero
Commercial & Residential Painting Specialist
Archie Guerrero is a Commercial and Residential Painting Specialist and the Operations Manager for DGP Painting in Austin, Texas. With a decade of experience, Archie specializes in interior and exterior painting and staining, cabinet refinishing, and wallpaper and popcorn removal. DGP Painting offers clients environmentally friendly paint materials and top-of-the-line paint products. DGP Painting has an A+ rating with the BBB and has been in Austin’s “Best of the Best.”

Archie Guerrero

Commercial & Residential Painting Specialist

Expert Answer

All you really need is to lightly scuff the old paint so the new coat has more to grab on and to bond.
Question

How do I protect my carpet when painting skirting boards?

Archie Guerrero
Commercial & Residential Painting Specialist
Archie Guerrero is a Commercial and Residential Painting Specialist and the Operations Manager for DGP Painting in Austin, Texas. With a decade of experience, Archie specializes in interior and exterior painting and staining, cabinet refinishing, and wallpaper and popcorn removal. DGP Painting offers clients environmentally friendly paint materials and top-of-the-line paint products. DGP Painting has an A+ rating with the BBB and has been in Austin’s “Best of the Best.”

Archie Guerrero

Commercial & Residential Painting Specialist

Expert Answer

Start by putting a piece of tape on the floor along the bottom of the baseboard. Use that line of tape to put some paper between the baseboard and the carpet. Then use another piece of tape to attach the paper down.
Question

Can I use silicone on skirting boards?

Archie Guerrero
Commercial & Residential Painting Specialist
Archie Guerrero is a Commercial and Residential Painting Specialist and the Operations Manager for DGP Painting in Austin, Texas. With a decade of experience, Archie specializes in interior and exterior painting and staining, cabinet refinishing, and wallpaper and popcorn removal. DGP Painting offers clients environmentally friendly paint materials and top-of-the-line paint products. DGP Painting has an A+ rating with the BBB and has been in Austin’s “Best of the Best.”

Archie Guerrero

Commercial & Residential Painting Specialist

Expert Answer

You can, but keep in mind that silicone caulk does not grab paint. If you want to paint over the caulk, you’ll need to use an acrylic latex one.

Warnings

Breathing in the vapors from some paints can be harmful, and it’s never good to inhale dust from sanding. Wear a face mask or respirator to protect your lungs.^{[26]
X
Research source}

⧼thumbs_response⧽
Helpful 0 Not Helpful 0
Test for lead-based paint before beginning to sand. This is a danger especially in older homes built before 1979. Use a dust wipe lead test kit if you suspect that you might need to sand lead-based paint.^{[27]
X
Research source}

⧼thumbs_response⧽
Helpful 0 Not Helpful 0