Easiest and Fastest Ways to Cut Copper Pipe to the Right Length

Cutting copper pipe for your DIY home project is actually super simple. You can use a pipe cutter, an autocut tool, or even a hacksaw if that's all you have on hand. We'll walk you through how to use each tool step-by-step so you can cut your copper pipe to the precise length you need. Keep reading to get started.

Method 1
Method 1 of 3:

Using a Pipe Cutter

  1. Image titled Cut Copper Pipe Step 4
    1
    Secure the tubing cutter to the pipe. Use the handle to open the jaws of the tubing cutter. Set the copper pipe into the jaws where you'd like to make the cut. Spin the handle to tighten the jaws firmly against the pipe.[1]
    • The tubing cutter acts like a vise to hold the pipe to the blade that's in the tool.
  2. Image titled Cut Copper Pipe Step 5
    2
    Score the pipe lightly. Hold the pipe with one hand and use your other hand to rotate the handle around the pipe once or twice. You should see a faint line around the pipe that was made by the blade cutting lightly into the pipe.[2]
    • This line will be a guide as you cut into the pipe.
    Advertisement
  3. Image titled Cut Copper Pipe Step 6
    3
    Turn and tighten the cutter. Continue to rotate the handle of the tool around the pipe so the blade keeps cutting into the pipe. Watch the blade to ensure that it's cutting into the same line and not spiraling down the pipe. Use the small knob on the base of the tool to tighten the cutter as you go. This will keep the blade on the same track.[3]
  4. Image titled Cut Copper Pipe Step 7
    4
    Remove the cutter and pull away the pipe. Loosen the tubing cutter and set it aside. You should be able to hold both ends of the pipe with the cut in the center. Bend the pipe to snap the cut portion away. You should see a clean cut with no metal filings or debris.[4]
    • If the pipe doesn't easily snap off, use the tubing cutter to make a clean cut through the pipe.
    5. Advertisement
Method 2
Method 2 of 3:

Using a Hacksaw

  1. Image titled Cut Copper Pipe Step 8
    1
    Select the right hacksaw blade. Use a hacksaw with a small gap between its teeth so it cuts cleanly through the copper pipe. Look for a hacksaw with a 32-TPI blade since it has the shortest distance between the teeth.
    • If the gap between the teeth is too large, the hacksaw will snag on the pipe.
  2. Image titled Cut Copper Pipe Step 9
    2
    Clamp the copper pipe, if possible. If the pipe is loose, set it in a vise so that the spot you want to cut extends a few inches (about 5 cm) from the jaws. This will give you space to cut. Spin the handle until the pipe is secured and doesn't move at all.
    • You may need to spin the handle a lot if you're using a thin pipe.
  3. Image titled Cut Copper Pipe Step 10
    3
    Mark the copper pipe. Determine where you'd like to make the cut on the copper pipe. Take a fine permanent marker and draw a line where you want the cut. After you've cut the pipe, you can wipe the mark off using rubbing alcohol.[5]
  4. Image titled Cut Copper Pipe Step 11
    4
    Set the hacksaw blade on the mark. Place the teeth of the hacksaw directly on the mark you made. Hold the handle of the hacksaw with your dominant hand use your other hand to support the top of the saw.[6]
  5. Image titled Cut Copper Pipe Step 12
    5
    Saw firmly into the pipe. Move the blade firmly across the pipe and lift it up as you bring the hacksaw back towards you. Set the blade back into the grove you've begun cutting and continue to push the saw blade into the pipe until the cut piece falls off.[7]
    • Avoid sawing in a backwards and forwards motion because you could damage the blade or make a ragged cut on the pipe.
  6. Image titled Cut Copper Pipe Step 13
    6
    Clean the cut copper pipe. Use a 4-in-1 cleaning tool to clean the cut pipe of any metal debris. Use the ends of the tool to brush inside the end of the pipe and place the center circle of the tool around the pipe itself. Rub the tool around the end so the metal bristles of the tool can brush and clean the pipe.[8]
    • Alternatively, you can cut a piece of sandpaper into a 1 in (2.5 cm) by 5 in (13 cm) strip. Wrap it around the pipe and vigorously pull both ends of the sandpaper back and forth.
    7. Advertisement
Method 3
Method 3 of 3:

Using an Autocut Tool

  1. Image titled Cut Copper Pipe Step 1
    1
    Select an autocut tool. If you're cutting copper pipe in a tight space (such as up against a corner), use an autocut tool. Measure the diameter of the pipe you want to cut and purchase an autocut tool for that exact size. Autocut tools are spring loaded so you won't be able to adjust the size of the cut.[9]
    • For example, for a small 1/2 inch (12 mm) pipe, buy a 1/2 inch (12 mm) autocut tool. Autocut tools come in 1/2 inch (12 mm), 3/4 inch (19 mm), and 1 inch (2.5 cm) sizes.
  2. Image titled Cut Copper Pipe Step 2
    2
    Clamp the autocut tool onto the copper pipe. Set the pipe into the center of the autocut tool where you'd like to make the cut. Secure the gray clamp down onto the pipe. The pipe should not be able to wiggle or slide out of the tool.[10]
  3. Image titled Cut Copper Pipe Step 3
    3
    Turn the tool 20 to 30 times. Look for the arrow on the tool that indicates which direction to turn it. Hold the pipe with one hand and use your other hand to turn the tool in the indicated direction. Turn the tool 20 to 30 times until the pipe is cut.[11]
    • The auto cut tool makes a clean, smooth cut, so you won't need to clean the pipe before using it.
    4. Advertisement

Things You'll Need

Cutting Copper Pipe with an Autocut Tool

  • Autocut tool in 1/2 inch (12 mm), 3/4 inch (19 mm), or 1 inch (2.5 cm)
  • Copper pipe

Using a Tubing Cutter

  • Tubing cutter
  • Copper pipe

Cutting Copper Pipe with a Hacksaw

  • Hacksaw with 32-TPI blade
  • Copper pipe
  • Vise
  • Permanent marker
  • 4-in-1 cleaning tool or sandpaper

You Might Also Like

Melt Copper
How to
Melt Copper
Oxidize Copper
How to
Oxidize Copper
Sell Copper
How to
Sell Copper
How to
Age Copper
Anneal Copper
How to
Anneal Copper
Darken Copper
How to
Darken Copper
Weld Copper
How to
Weld Copper
Remove Copper on the Surface of Materials
How to
Remove Copper on the Surface of Materials
Solder Copper Tubing
How to
Solder Copper Tubing
Hammer Copper
How to
Hammer Copper
Advertisement

References

  1. ↑ https://www.thisoldhouse.com/how-to/how-to-cut-plumbing-pipes-and-tubing
  2. ↑ https://www.thisoldhouse.com/how-to/how-to-cut-plumbing-pipes-and-tubing
  3. ↑ https://www.thisoldhouse.com/how-to/how-to-cut-plumbing-pipes-and-tubing
  4. ↑ https://www.thisoldhouse.com/how-to/how-to-cut-plumbing-pipes-and-tubing
  5. ↑ http://bpec.org.uk/wp-content/uploads/2016/01/BPEC-Essential-Plumbing-Skills-Copper-Pipefinal-version.pdf
  6. ↑ http://www.technologystudent.com/equip_flsh/hacksw2.html
  7. ↑ http://www.technologystudent.com/equip_flsh/hacksw2.html
  8. ↑ https://www.familyhandyman.com/plumbing/how-to-solder-copper-pipe-joints/view-all/
  9. ↑ https://www.youtube.com/watch?v=FRY0_5Jh574
  1. ↑ https://www.youtube.com/watch?v=FRY0_5Jh574
  2. ↑ https://www.youtube.com/watch?v=FRY0_5Jh574

About This Article

Jessica Gibson
Co-authored by:
Jessica Gibson
wikiHow Staff Writer
This article was co-authored by wikiHow staff writer, Jessica Gibson. Jessica Gibson is a Writer and Editor who's been with wikiHow since 2014. After completing a year of art studies at the Emily Carr University in Vancouver, she graduated from Columbia College with a BA in History. Jessica also completed an MA in History from The University of Oregon in 2013. This article has been viewed 109,538 times.
2 votes - 50%
Co-authors: 8
Updated: November 7, 2022
Views: 109,538
Categories: Piping | Metalworking | Copper
Article SummaryX

To cut a copper pipe, start by selecting the correctly sized autocut tool according to the diameter of the pipe, which is usually between 1/2-inch and 1-inch. Then, clamp the autocut tool onto the pipe exactly where you want it cut and make sure it’s tight so it won’t slide off or wiggle. Next, hold the pipe with one hand and use the other hand to turn the tool around the pipe 30 times, or until it’s cut through. For tips from our Handyman reviewer on how to cut a copper pipe with a tubing cutter or hacksaw, read on!

Did this summary help you?
Advertisement